Abstract:…id solution alloys to produce complex net-shaped plasma-facing com ponents of the desired tungsten alloys, without the high impurity levels, porosity, complexity, and cost associated with alternative processing such as melting, sintering of powders, or homogenization heat… more
Abstract:…successful from space, and they do not characterize the surface, with sufficient detail and timeliness for albedo to be estimated, so that the local mass balance of the various Arctic sea ice types, including snow cover and open water, cannot be correlated with heat balance… more
Abstract:…rface to a high quality super-finished surface. This level of friction reduction is consistent for both low and high speeds. Phase I shows that costly super-finishing processes can be avoided with special oil formulations that polish surfaces while running. Gear steel heat… more
Abstract:… pairs of panels, with either tray or conveyor belt operation). Multiple interlocks, self shielding of the sources, and lead wall linings ensure safe operation. All three models will have dose rates & gt; 8 Gy/min; closed loop oil heat exchangers;… more
Abstract:…evelop a new Thermal Hydrogen Extractor on Board (THEB) system. It is based on a new POC-developed technology of hydrogen generation and COTS components to extract and supply this hydrogen. The innovation in system design will enable the THEB system to utilize the dissipated … more
Abstract:… end of the effort, a prototype system capable of sintering research samples will be delivered. BENEFIT: The anticipated benefits/commercial applications of the Phase II R & D are low-cost, high-performance ceramic coatings in high-temperature applications such as heat… more
Abstract:…lopment of CMC components by the Air Force and its major aerospace engine suppliers. In Phase I the feasibility of using this methodology has been demonstrated by qualitative comparison with experimental observations of open porosity. Basic elements of mass and heat transfer… more
Abstract:…hot water heater (HWH) have resulted in hot water heaters so loud that they cannot feasibly be used in residential applications. This project entails the development and prototyping of a hybrid hot water heater compressor which drastically reduces the energy needed to heat hot… more
Abstract:… are expected to play a key role in unraveling the mysteries of nuclear physics, nuclear astrophysics, and fundamental interactions at low energies. This project will develop refractory tungsten powders as catchers which retain open porosity after extended heating at high… more
Abstract:GEOST and the University of Arizona propose to develop and demonstrate the Weaponized Heating of Ignited Plasma Acoustic Modulation (WHIP-AM). This device produces acoustic signals at long range thereby providing the capability to convey messages and produce irritating acoustic… more
Abstract:… extrusion processing at PolymerPlus. PbPc blended PC films will be stacked to achieve PbPc concentration gradient as per NLO design. Film stack will be consolidated into a sheet and shaped into a curved surface ("preform") using metallic molds under heat and pressure… more
Abstract:…ldable laboratory grade EEG monitoring system. PsiKick will develop a complete schematic-level design for the SoC that leverages the ultra-low power wireless platform developed at PsiKick based on a demonstrated wireless ECG monitor powered exclusively from body heat with no… more
Abstract:This proposal will result in innovative and life-saving software enabling first responders to easily see a heat map showing the probability of area for the
missing person. Sending teams to the right area saves lives, resources, and time. New research into geographic models of… more
Abstract:Generation IV Gas-Cooled Reactors require advanced structural materials capable of resisting
extreme conditions of radiation exposure, high heat flux, corrosive environments and thermo- mechanical stresses. Metallic alloys such as stainless steel and Zircaloy used in… more
Abstract:A major problem with nuclear fission reactors is the welding of components of dissimilar metals, where the filler is usually of an additional metal alloy that is not necessarily the same as the two parts to be joined. Welding of metals will often have a heat affected zone (HAZ)… more
Abstract:… sources will be addressed with the development of innovative advances to their design. Our field emitters are projected to exhibit narrower emission angles, better voltage characteristics, smaller and more perfect tip shapes, higher mechanical stability, better heat… more
Abstract:… Suit (TALOS) program is tasked with integrating several systems that require electric power. While systems such as internal combustion engines could conceivably meet the 4-5kW projected power requirement in a manageable package, this would result in undesirable heat and… more
Abstract:… photons per pulse. However, the lasers currently used to pump them operate at low repetition rate, severely limiting their potential to generate high average powers. This limitation is the result of deleterious thermal effects in the flash-lamp pumped lasers used to heat the… more
Abstract:… of Phase I, to develop innovative magnet wire insulation for motor windings that results in increased power density and operating efficiency. This will be achieved by developing a wire insulation that has as much as 10 times higher thermal conductivity so that heat… more
Abstract:… research. Existing devices have relatively slow switching times, compared to those required for the application. The proposed program seeks to develop high-voltage, high-current devices with much faster switching times and reduced conduction losses, thereby reducing heat… more
Abstract:… inside battery, as well as the operation of biological systems. Currently, a few liquid stages at synchrotrons have been home-built and suffer from leaks, are extremely cumbersome to use and do not provide any additional capabilities such as electrical biasing and … more
Abstract:… environmental parameter measurement and control issues. These goals will be accomplished by developing and bringing to market a new in-situ TEM microfluidic holder that contains an integrated, microfabricated pH sensor and temperature sensor in addition to a heating element. … more
Abstract:ABSTRACT: Current waste heat management technologies from satellite payload including the sensor, control and actuators, are bulky and energy inefficient because they cannot provide on-demand site-specific cooling. Fluidic systems are not desirable for satellite applications… more
Abstract:Water heating is the second largest source of energy consumption in a household. Almost half of them are electricity based which are quite inefficient. Current crop of heat pump water heaters are too expensive to make a meaningful impact on the situation. This is the overall… more
Abstract:…urs or 5 Billion cycles. The miniature sensing head and signal conditioner enable sensor integration with a diesel fuel injector or packaging as a stand-alone device. Unlike the current Optrand"s dynamic cylinder pressure sensor that uses a recessed diaphragm and a heat… more
There are several categories such as “By Agency”, “By Year”, “By State” etc.
Select a checkbox within a category to refine your search results.
Each of your selections is listed in the “Narrow Search Filters” bar. You can uncheck these selections to remove them.
Search for Either Criteria
When you select multiple values within a category, the results will include values that match either of the selections.
For example, selecting “2005” and “2007” in the “By Year” category will display results that include either 2005 OR 2007 in the results.
Narrowing the Search Results
You can refine your search results across categories. To narrow down your results, select multiple values across different categories. The results will only include values that match the selections across the categories.
For example, selecting “2005” in the “By Year” category and “NASA” in the “By Agency” category will only display the results that contain both “2005” AND “NASA” in the results.