You are here

Electrically Small Antennas at High Frequency

Description:

OUSD (R&E) CRITICAL TECHNOLOGY AREA(S): Sustainment

 

The technology within this topic is restricted under the International Traffic in Arms Regulation (ITAR), 22 CFR Parts 120-130, which controls the export and import of defense-related material and services, including export of sensitive technical data, or the Export Administration Regulation (EAR), 15 CFR Parts 730-774, which controls dual use items. Offerors must disclose any proposed use of foreign nationals (FNs), their country(ies) of origin, the type of visa or work permit possessed, and the statement of work (SOW) tasks intended for accomplishment by the FN(s) in accordance with the Announcement. Offerors are advised foreign nationals proposed to perform on this topic may be restricted due to the technical data under US Export Control Laws.

 

OBJECTIVE: Design, develop, simulate and demonstrate an electrically small antenna using metamaterials that can operate at frequencies from 2–30 MHz. The antenna will be used to transmit/receive Skywave radio-wave signals to provide Beyond Line of Sight (BLOS) communications on Navy aircraft.

 

DESCRIPTION: In the absence of satellite communication channels, current and future missions require aircraft to communicate at High Frequencies (HF) for BLOS communications. The principle constraint on modern air platforms are size and weight which drives the need for smaller, lighter, efficient radio and antenna technologies. The innovative use of metamaterials has shown to be a promising technology to reduce size and weight while achieving effective power characteristics when compared to conventional antenna designs at other portions of the RF spectrum. Therefore, it is hypothesized that the use of metamaterials in antenna design could dramatically reduce the size of the antenna and may improve other antenna parameters such as enhancing bandwidth and increasing gain at HF. The challenge is to determine if metamaterials can significantly reduce the size and weight of an HF antenna, be affordable, and be suitable for installation on Navy platforms. Innovative solutions are being sought to develop an HF antenna that can meet the design goals shown below. In addition, there is the need for a conformal antenna to minimize drag on the aircraft and reduce risk of damage.

 

Antenna Design Goals:

(a) Weight—reduced in half as compared to conventional

(b) Volume—1/5 as compared to conventional

(c) VSWR—No worse than conventional, over full frequency range, 2-30 MHz

(d) Gain—3 dB improvement over conventional

 

Conventional HF Antenna Examples:

(a) Chelton 435 Towel Bar Antenna, appx 8 in. (20.3 cm) stand off from aircraft skin (moldline) by 10 ft long (3 m)

(b) Shunt-fed embedded HF antenna found in airplane vertical stabilizer

 

Work produced in Phase II may become classified. Note: The prospective contractor(s) must be U.S. owned and operated with no foreign influence as defined by 32 U.S.C. § 2004.20 et seq., National Industrial Security Program Executive Agent and Operating Manual, unless acceptable mitigating procedures can and have been implemented and approved by the Defense Counterintelligence and Security Agency (DCSA) formerly Defense Security Service (DSS). The selected contractor must be able to acquire and maintain a secret level facility and Personnel Security Clearances. This will allow contractor personnel to perform on advanced phases of this project as set forth by DCSA and NAVAIR in order to gain access to classified information pertaining to the national defense of the United States and its allies; this will be an inherent requirement. The selected company will be required to safeguard classified material during the advanced phases of this contract IAW the National Industrial Security Program Operating Manual (NISPOM), which can be found at Title 32, Part 2004.20 of the Code of Federal Regulations. Reference: National Industrial Security Program Executive Agent and Operating Manual (NISP), 32 U.S.C. § 2004.20 et seq. (1993). https://www.ecfr.gov/current/title-32/subtitle-B/chapter-XX/part-2004

 

PHASE I: Investigate suitable metamaterials for an antenna at HF, create a digital model, and demonstrate the feasibility of the design to meet the antenna goals defined above. Document—with detailed analysis—the predicted performance with modeling and simulation. The Phase I effort will include prototype plans to be developed under Phase II.

 

PHASE II: Using the results from Phase I, develop a prototype antenna; demonstrate in the lab, and/or chamber that the prototype can transmit and receive at HF; and measure the performance of the prototype across the frequency band. Work with NAVAIR to perform initial qualification testing on sample sections of the antenna to gain insight into suitability of the design to operate under representative conditions. Deliverables of Phase II will be the prototype array and a final report, which documents the performance of the prototype.

 

Work in Phase II may become classified. Please see note in Description paragraph.

 

PHASE III DUAL USE APPLICATIONS: Further develop the prototype produced in Phase II and work with the Navy to install on a rotorcraft. Demonstrate that the antenna can transmit and receive at HF for a military application.

 

This technology would be extremely useful for other airborne systems such as law enforcement, safety, and corporate transport. The technology would be helpful for situations where SATCOM is too expensive, not viable (e.g., Polar Regions or deep valleys), and if the SATCOM hardware is too large.

 

REFERENCES:

  1. IEEE Standards Association. (2013). 145-2013-IEEE standard for definitions of terms for antennas. IEEE, New York, NY. https://doi.org/10.1109/IEEESTD.2014.6758443
  2. Krzysztofik, W. J., & Cao, T. N. (2018). Metamaterials in application to improve antenna parameters. Metamaterials and Metasurfaces, 12(2), 63-85. https://books.google.com/books?hl=en&lr=&id=oC-RDwAAQBAJ&oi=fnd&pg=PA63&dq=Metamaterials+in+Application+to+Improve+Antenna+Parameters&ots=F_Jb40rzlu&sig=rsAi0lyahtmZ1yvHgD4FCfBvbsc#v=onepage&q=Metamaterials%20in%20Application%20to%20Improve%20Antenna%20Parameters&f=false
  3. The MIL-STD-810 Working Group. (2008, October 31). Department of Defense test method standard: Environmental engineering considerations and laboratory tests. Department of Defense. https://www.atec.army.mil/publications/Mil-Std-810G/MIL-STD-810G.pdf
  4. Kumar, P., Ali, T., & Pai, M. M. (2021). Electromagnetic metamaterials: A new paradigm of antenna design. IEEE Access, 9, 18722-18751. https://doi.org/10.1109/ACCESS.2021.3053100
  5. Chelton Limited. (n.d.). 435, 455, 465, 475 & 485 towel rail antenna arrays. Chelton. https://www.chelton.com/media/0fuhgecl/chelton-435-465-455-485-towel-rail-antenna-arrays.pdf

 

KEYWORDS: antenna; high frequency wavelength; electrically small antenna; ESA; metamaterials; military helicopters; Beyond Line of Sight; BLOS; Skywave HF Transmissions

US Flag An Official Website of the United States Government