Company

Portfolio Data

Icon: back arrowBack to Company Search

IMPOSSIBLE OBJECTS, INC.

Address

3455 COMMERCIAL AVE
NORTHBROOK, IL, 60062-1818
USA

View website

UEI: LJJ5XAB5VNG1

Number of Employees: 24

HUBZone Owned: No

Woman Owned: No

Socially and Economically Disadvantaged: No

SBIR/STTR Involvement

Year of first award: 2021

11

Phase I Awards

8

Phase II Awards

72.73%

Conversion Rate

$1,139,664

Phase I Dollars

$9,697,852

Phase II Dollars

$10,837,515

Total Awarded

Awards

Up to 10 of the most recent awards are being displayed. To view all of this company's awards, visit the Award Data search page.

Seal of the Agency: DOD

High-Volume Low-Cost Long-range Fixed Wing UAS with near-conflict Distributed Manufacturability

Amount: $1,249,985   Topic: AFX255-DPCSO3

Impossible Objects is proposing to develop a low-cost fixed-wing high-strength long-distance unmanned aerial system (UAS) that can be manufactured in volume. To do this Impossible Objects (a high-speed 3D-printing company) will use a design developed by Titan Dynamics (an unmanned aerial vehicle design company) to develop a Group 2 UAS capable of the following:A) Range: Exceeds 1,000 miles (Stretch goal: Exceeds 2,000 miles) B) Price: Airframe costs less than $8K (Stretch goal: Less than $4K) C) Manufacturing speed: One airframe every 4 hours (Stretch goal: One every 2 hours) D) Arbitrary payload: Equipped with both a payload bay and drop pylons Proving a design that can be manufactured at these costs and at these rates with this long-distance capability would be an unmatched asset for the U.S.A.F. at a critical time in the evolution of warfare.

Tagged as:

SBIR

Phase II

2025

DOW

USAF

Seal of the Agency: DOD

Near Expeditionary Advanced Manufacturing of Engine Cooling Fans for Wheeled Vehicles

Amount: $249,706   Topic: A244-070

The R&D efforts of this proposal will contribute to solving the Army’s need to develop and integrate near expeditionary advanced manufacturing solution for producing engine cooling fans for wheeled vehicles. Impossible Objects will study integration of our Composite Based Additive Manufacturing (CBAM) 3D printing capabilities and how this capability will allow for Rapid Adaption of maintenance capabilities to address Army Sustainment Gaps for Next Generation Combat Vehicles in support of Large-Scale Combat Operations (LSCO). 

Tagged as:

SBIR

Phase I

2025

DOW

ARMY

Seal of the Agency: DOD

Low Cost Additive Manufacturing of Radiation Shielding Material & Structures

Amount: $149,996   Topic: MDA23-P001

The research and development efforts of this proposal will contribute to solving the Radiation Hardened Microelectronics (RadHard ME) mission needs for space platforms, specifically regarding shielding from radiation effects including Heavy Ion, X-ray Proton, and Pulsed Neutron Single Event Effects. This is especially critical with increased miniaturization of space platforms (i.e. CubeSats), where the most challenging aspects are the space and weight limitations for these enclosures, which must fit into predetermined tight spaces with strict weight limitations. Approved for Public Release | 24-MDA-11906 (16 Sep 24)

Tagged as:

STTR

Phase I

2024

DOW

MDA

Seal of the Agency: DOD

Additively Manufactured Embedded Wiring Harnesses

Amount: $239,987   Topic: N232-086

To address the NavyÆs need for novel UAV multifunctional weight-saving structural technologies, Impossible Objects proposes to use its novel composite additive manufacturing technology to embed wire harnesses into structural UAV parts. If successful, this will be the first scalable method to integrate high-current wiring into high-strength lightweight composite parts using a high-volume manufacturing process. While providing weight savings, this added capability will add many additional functionalities. In particular, it will also enable near frontline manufacturing in areas affected by contested logistics with volumes measured in thousands of UAVs per printer per month, while also a) reducing the heat signature of the UAV and allowing for electrical redundancy at no additional cost or impact to throughput, b) greater UAV robustness, c) lower drag, and d) far lower assembly times. In Phase I, Impossible Objects will demonstrate that high current wiring can be embedded into their parts and characterize the impact, if any, to the material performance. In Phase II, this will be extended to embed a full wiring harness in a UAV chassis and prove out the scalability of the manufacturing process.

Tagged as:

SBIR

Phase I

2024

DOW

NAVY

Seal of the Agency: DOD

Optimization of High-Speed Post-Processing Equipment (TACFI)

Amount: $1,898,311   Topic: AF221-DCSO1

Composites Based Additive Manufacturing (CBAM) technology is the world’s fastest AM technology by over 15x (and up to 1,000x depending on the technology). With a speed-boost like this the post-processing steps have not yet achieved the same cycle time, meaning that to achieve the same throughput multiple post-processing machines are needed. While this is a viable and reasonable solution frequently implemented elsewhere throughout modern manufacturing, this activity focuses on novel approaches that should be able to sync the post-processing cycle time with that of the high-speed CBAM printer. If successful, this project will reduce complexity, labor, and cost in measurable and meaningful ways. In particular, the proposed effort will upgrade, in parallel, the two CBAM post-processing steps, with a target to reduce the end-to-end 4-5 hour post-processing cycle time for a single 1”-tall build block down to less than an hour. When manufacturing 100s of build blocks, this type of optimization fundamentally changes the operational dynamics, providing far greater adaptability to constrained logistics and higher throughput with lower labor, time, and cost. The increase of the speed of the CBAM production process by four times will significantly impact AFRL/RX and HQ ACC’s ability to fulfill mission needs at every level, from current conflict areas to potential near peer adversaries in the future.

Tagged as:

SBIR

Phase II

2024

DOW

USAF

Seal of the Agency: DOD

3D-Printed Parts with Embedded Electronics

Amount: $74,998   Topic: X22D-OTCSO1

Due to the limitations of traditional manufacturing, vehicle design has required that components of all kinds are separate pieces.  Electronics is no exception.  Today, vehicle electronics are typically consolidated into one or two places and sensors are so expensive that they are only used where they are critical. IO’s 3D-printing process can allow for decentralized electronics designs that allow engineers to optimize for cost and functionality, rather than be limited by the design requirements of traditional manufacturing.

Tagged as:

STTR

Phase I

2023

DOW

USAF

Seal of the Agency: DOD

Rapid Response 3D Printing for MX, Repair, & Overhaul

Amount: $74,998   Topic: X22D-OTCSO1

IO’s CBAM technology can scale to speeds competitive with the world’s fastest manufacturing technologies (e.g., injection molding), while retaining high tolerance, industry-leading material properties, and all of the incredible benefits of 3D printing (e.g., no tooling costs, immediate manufacturability, much greater design flexibility, etc.).  This is not just theoretical.  IO has already printed parts 10x faster than any other comparable 3D-printing technology, using its prototype NextGen printer.

Tagged as:

STTR

Phase I

2023

DOW

USAF

Seal of the Agency: DOD

Electromagnetic-Pulse Protected Electronics Enclosures

Amount: $74,998   Topic: X224-OCSO1

Typically, anti-EM warfare protection is done by enclosing all electronics in metal electrical boxes.  However, this strategy is limited in several ways:  Firstly, many electronics boards must fit into tight spaces, where the typical machined-metal boxes either can’t fit or cost significant amounts of money to be manufactured; secondly, many electrical boards can overheat when enclosed in a box, limiting heat dissipation; and, thirdly, metal boxes tend to add critical weight to the drone, where every pound is important. This project will explore a method to inexpensively fabricate, using a high-speed high-performance 3D-printing system, anti-EM warfare electrical boxes, which mitigate each of the above challenges.

Tagged as:

SBIR

Phase I

2023

DOW

USAF

Seal of the Agency: DOD

Composite Based Additive Manufacturing Scaling of Throughput, Volume, and Speed

Amount: $1,799,971   Topic: AF21A-TCSO1

The current Phase II project is expanding the CBAM material offerings to include uniaxial carbon-fiber substrates into the CBAM process.  It has already been shown that the strength and stiffness have improved by at least 250-300% (3.5-4x stronger and sti

Tagged as:

STTR

Phase II

2023

DOW

USAF

Seal of the Agency: DOD

Additive Manufacturing of UAV Parts with Embedded Circuits for Detecting Part Failures

Amount: $1,249,978   Topic: AFX234-DCSO2

Impossible Objects (IO) has created a fundamentally new approach to additive manufacturing (AM) called Composite Based Additive Manufacturing (CBAM). CBAM is a superior 3D-printing process, because the material properties of the parts are better, the proc

Tagged as:

SBIR

Phase II

2023

DOW

USAF