You are here

Home

EDWARD POPE DR

Company Information
Address
31304 VIA COLINAS STE 102
WESTLAKE VILLAGE, CA 91362-4586
United States


http://www.matechgsm.com
Information

UEI: HPX4PC9TMCV5

# of Employees: 6
Ownership Information

HUBZone Owned: No

Socially and Economically Disadvantaged: No

Woman Owned: No

Award Charts




Award Listing

  • Record 1 TO 73

  1. Low Cost Net-to-Shape Fiber Preforms for Complex-Shaped CMCs.

    Amount: $950,588.00

    This Phase II NAVAIR SBIR Program seeks to demonstrate the real CMC component fabricability and scale-ability for complex shaped JSF turbine engine components such as a blade, vane, and/or shroud, usi ...

    SBIRPhase II2007Department of Defense Navy

  2. High specific-strength C-Zr(O)C / C-ablator TPS for CEV

    Amount: $99,964.00

    This Phase I NASA SBIR Proposal seeks to demonstrate a new zero-erosion ablative thermal protection system (TPS) technology that is based upon an ultra-high temperature (UHT) ceramic fiber pre-form / ...

    SBIRPhase I2007National Aeronautics and Space Administration

  3. Solid Rocket Motor Nozzles Made From Tantalum Carbide Continuous Fiber Composites for Boost Applications

    Amount: $1,050,000.00

    This Air Force Phase II SBIR program seeks to further develop the first tantalum carbide (TaC) structural ceramic fiber for TaC(f)/TaC(m) CMCs for use in aluminized propellant solid rocket motor (SRM) ...

    SBIRPhase II2007Department of Defense Air Force

  4. Weaveable HfC Structural Fiber Development and Scale-Up

    Amount: $750,000.00

    This MDA Phase II SBIR program seeks to further develop the first HfC structural ceramic fiber for HfC(f)/HfC(m) CMC fabrication. MATECH/GSM proposes to scale-up HfC structural ceramic fiber to a leve ...

    SBIRPhase II2007Department of Defense Missile Defense Agency

  5. Low Cost Si-BN interface Coatings for SiC/SiNC CMCs.

    Amount: $743,398.00

    This Phase II NAVAIR SBIR Program seeks to demonstrate the Reactive Transformation Process (RTP) as an alternative innovative new class of interfacial coating method (to the conventional CVI) for 2-D ...

    SBIRPhase II2007Department of Defense Navy

  6. Manufacturing of CMC Combustor Liners for Gas Turbine Generators

    Amount: $750,000.00

    The use of ceramic matrix composites (CMCs) would permit higher efficiency power generation for the stationary gas turbine engines used in electricity production. However, current CMC systems do not ...

    SBIRPhase II2007Department of Energy

  7. Low Cost High Performance 3-D CMCs for Jet Engine Components

    Amount: $257,469.00

    This Phase II NAVAIR SBIR Program seeks to demonstrate the real CMC component fabricability and scale-ability for JSF flaps and seals using the MATECH GSM (MG)-developed and optimized low-cost SiNC po ...

    SBIRPhase II2006Department of Defense Navy

  8. Weaveable HfC Structural Fiber Development and Scale-Up

    Amount: $100,000.00

    In this MDA Phase I SBIR program, MATECH/GSM proposes to further develop and scale-up HfC structural ceramic fiber to a level suitable for low rate initial production (LRIP) of HfC ceramic fiber tow d ...

    SBIRPhase I2006Department of Defense Missile Defense Agency

  9. Solid Rocket Motor Nozzles Made From Tantalum Carbide Continuous Fiber Composites for Boost Applications

    Amount: $100,000.00

    In this proposed Air Force Phase I SBIR Program, MATECH/GSM seeks to develop woven TaC ceramic fiber reinforced TaC matrix CMCs for aluminized propellant solid rocket motors (SRMs). An example system ...

    SBIRPhase I2006Department of Defense Air Force

  10. Non-Ablative 5000F MKV Divert Valve Insulator

    Amount: $500,000.00

    This Phase II MDA SBIR Program seeks to demonstrate a new high temperature non-ablative 5000F MKV divert valve insulator. ATK (Elkton, MD)is designing the MKV Divert Valve and has experienced unaccept ...

    SBIRPhase II2006Department of Defense Missile Defense Agency
US Flag An Official Website of the United States Government