You are here

UES, Inc.

Company Information
Address
4401 Dayton Xenia Rd
Dayton, OH 45432-1805
United States


HTTP://WWW.UES.COM

Information

DUNS: 074689217

# of Employees: 280


Ownership Information

HUBZone Owned: No

Socially and Economically Disadvantaged: No

Woman Owned: Yes



Award Charts




Award Listing

  1. Fabrication of Ta-Hf-C-based Ultra High Temperature Composites

    Amount: $500,000.00

    This Phase II STTR program seeks a new fabrication method to produce stronger (>100 kpsi) and tougher (>10 MPam1/2) ultra-high temperature HfC-based composites (UHTC) with an outstanding oxidation res ...

    STTRPhase II2014Department of Defense Missile Defense Agency
  2. Durable CMAS Resistant Thermal Barrier Coatings

    Amount: $100,000.00

    Thermal barrier coatings (TBCs) are susceptible to damage under service conditions due to environmental contaminants such as calcium-magnesium-aluminum-silicon-oxide systems (CMAS). In this Phase I SB ...

    SBIRPhase I2013Department of Defense Army
  3. Improved Rotorcraft Transmission Survivability Under Loss-of Lubrication

    Amount: $100,000.00

    Loss of the primary lubrication system in the power transmission system can result in an immediate or rapid failure of the drive system of military air and ground vehicles. This proposal offers a comb ...

    SBIRPhase I2013Department of Defense Army
  4. HIGH STRENGTH AND TOUGHNESS TUNGSTEN CARBIDE (WC) WITH NON-COBALT (Co) MATRICES

    Amount: $100,000.00

    Cemented cobalt-tungsten carbide is a material with attractive properties including high hardness and fracture toughness that has found success in a wide variety of applications ranging from drilling ...

    STTRPhase I2013Department of Defense Army
  5. Modeling and Simulation of Ceramic Matrix Composite (CMC) Processing by Polymer Infiltration and Pyrolysis

    Amount: $150,000.00

    ABSTRACT: The challenge for manufacturing ceramic matrix composites using the preceramic polymer infiltration and pyrolysis (PIP) method is to ensure a fully dense matrix. Material loss during a pyr ...

    SBIRPhase I2013Department of Defense Air Force
  6. Process Modeling for Additive Manufacturing of Alloys by Electron Beam

    Amount: $150,000.00

    ABSTRACT: UES proposes to obtain data to anchor models for additive manufacture by electron beam melting (EBM). In this process, parts are made by scanning an electron beam in a raster defined by a ...

    SBIRPhase I2013Department of Defense Air Force
  7. Frequency Domain-based Electrical Accumulator Unit (EAU)

    Amount: $150,000.00

    ABSTRACT: Military aircraft are steadily moving towards the"More Electric Aircraft (MEA)"concept where large flight loads like hydraulic actuators are replaced with electrical analogs powered by high ...

    SBIRPhase I2013Department of Defense Air Force
  8. Development of New Processes for the Refurbishment of Infrared Search and Track (IRST) Germanium (Ge) Domes

    Amount: $80,000.00

    Infrared search and track (IRST) single crystal Ge domes develop surface defects after extensive use in adverse environments such as sandstorms, rain and fog. Surface defects on Ge domes lead to a red ...

    SBIRPhase I2013Department of Defense Navy
  9. Innovative Passivation Technologies for Aluminum Nanoparticles

    Amount: $514,419.00

    Aluminum nanopowders (nano-Al) possess surface areas on the order of 20-40 m2/g and have attracted interest throughout the energetics community for propellant and metallization applications. Aluminum ...

    SBIRPhase II2013Department of Defense Army
  10. Non-invasive Blood Alcohol Sensor for Emergency Room Applications

    Amount: $149,998.00

    DESCRIPTION (provided by applicant): Measurements of cell viability (percentage live versus dead cells) may be used to evaluate: cellular damage due to toxins, the effect of infection, response to dru ...

    SBIRPhase I2013Department of Health and Human Services National Institutes of Health
US Flag An Official Website of the United States Government