List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for the given year is not complete until April of the following year. Annual Reports data is a snapshot of agency reported information for that year and hence might look different from the live data in the Awards Information charts.

  1. Transportation Vehicle Waste Heat Recovery System

    SBC: MMPG LLC            Topic: 101FT1

      A one-cylinder diesel engine will be modified to achieve a 20% to 40% improvement in fuel efficiency.  This will be accomplished by insulating the interior of the combustion chamber with a proprietary thermal insulating material.  Heat normally transferred to the engine coolant through the walls of the head, cylinder and piston will be retained within the combustion chamber where ...

    SBIR Phase I 2010 Department of Transportation
  2. Software Package for Material Model Evaluation

    SBC: APTEK, Inc.            Topic: N/A

    This Phase I and II SBIR will develop a user-friendly, run-time efficient software package dedicated to fitting and evaluating material models used in finite element codes like LS-DYNA. The software package will consist of a pre-processor, a core driver, and a post-processor. The pre-processor will allow the user to specify the material model, model parameters, and desired load history. The dri ...

    SBIR Phase II 2004 Department of Transportation
  3. Portland Cement Concrete Pavement Recycling

    SBC: Road Processing Resources Inc.            Topic: N/A

    RPR's Phase I contract proved the feasibility of concrete recycling based o a shock-producing hammer/anvil concept for fracturing and sizing aggregate and separating reinforcing steel into marketable scrap. The Phase II project will develop a portable self-propelled prototype to remove and process a 12 foot wide roadway at a rate of about a mile a day. This is called "Fast Track" highway removal ...

    SBIR Phase II 2004 Department of Transportation
  4. Software Package for Material Model Evaluation

    SBC: APTEK, Inc.            Topic: N/A

    This Phase I and II SBIR will develop a user-friendly, run-time efficient software package dedicated to fitting and evaluating material models used in finite element codes like LS-DYNA. The software package will consist of a pre-processor, a core driver, and a post-processor. The pre-processor will allow the user to specify the material model, model parameters, and desired load history. The dri ...

    SBIR Phase I 2001 Department of Transportation
  5. A New Nanocomposite Rubber Liner for Tires

    SBC: TDA Research, Inc.            Topic: N/A

    Halobutyl rubber is used as an inner liner for tubeless automotive tires because of its low permeability to gases and good compatibility with other tire materials. However, at high pressures and over prolonged time periods, tires leak. Factors such as under-inflation and heat are major contributors to tire damage. While the tires are slowly losing air pressure, consumers also do not maintain c ...

    SBIR Phase I 2001 Department of Transportation
  6. Recycling of Portland Cement Concrete

    SBC: Road Processing Resources Inc.            Topic: N/A

    This proposal is to investigate a concept of a shock producing component that will be the basis of a machine to remove deteriorated concrete pavement. The principal has been proven feasible, but further demonstration has to be accomplished to proceed with application and expense of continued development of a Road Remover/Recycler. This machine will move continuously on a lane width of pavement a ...

    SBIR Phase I 2001 Department of Transportation
  7. N/A

    SBC: Raymond & Lae Engineering,            Topic: N/A

    N/A

    SBIR Phase II 1999 Department of Transportation
  8. Rapid-Scan Noninvasive Stress Measurement Technology

    SBC: Stress Sensors, Inc.            Topic: N/A

    Not Available A number of shortcomings in current active control systems preclude their widespread use: 1) need for higher actuator authority, 2) need for robust compact actuators with ease of implementation, and 3) need for improved power handling and driving electronics. The innovation proposed is a new approach to active material and electronic systems for the control of vibrations in aeroelas ...

    SBIR Phase I 1999 Department of Transportation
  9. Microwave NDT of Cracks in Structural Metals

    SBC: Raymond & Lae Engineering,            Topic: N/A

    N/A

    SBIR Phase I 1997 Department of Transportation
  10. Digital Waveform-Based System for Acoustic Emission Measurement for Nondestructive Testing of Structural Steel

    SBC: Digital Wave Corp.            Topic: N/A

    Digital Wave Corporation proposed to develop a novel nondestructive testing (NDT) system for high speed acquisition and analysis of wide band acoustic emission (AE) waveforms. The system will provide the capability to detect, identify and locate crack growth in loaded steel structures. This system will incorporate the new high fidelity sensor developed by the Federal Highway Administration and a ...

    SBIR Phase I 1996 Department of Transportation

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government