You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. DEVELOP SAND-PLUGGING RESISTANT METALLIC COMBUSTOR LINERS

    SBC: Phoenix Analysis and Design Technologies, Inc.            Topic: A19002

    Gas turbine engines that operate in regions with high concentrations of dust/sand are prone to suffer accelerated deterioration due to erosion, plugging, melting, deposition, coating degradation and consequential damage. Dust/sand ingested into the inlet of gas turbine engines is pulverized by the turbomachinery to ultra-fine size, typically less than 10 micrometers. The ultra-fine dust is difficu ...

    SBIR Phase I 2019 Department of DefenseArmy
  2. Virtual Ground for Enabling Autonomous Refueling

    SBC: Auv LLC            Topic: A18135

    The AR3P (Autonomous & Robotic Remote Refueling Point) is in need of a reliable and efficient grounding system. Traditional grounding systems are semi-permanent structures that require a 6 to 9 foot grounding rod be installed into terrain. This proposal outlines the development of a virtual ground for enabling autonomous refueling which will eliminate the need for this grounding stake. By “freei ...

    SBIR Phase I 2019 Department of DefenseArmy
  3. Charge collection scanning transmission electron microscopy for advanced infrared semiconductor devices

    SBC: FABMETRIX, INCORPORATED            Topic: A19046

    Techniques for the reduction of growth-induced crystal defects are of critical importance to the efforts geared toward development of thin-film heteroepitaxial materials and devices for infrared sensor applications based on large-area semiconductor substrates. These defects, such as threading and misfit dislocations, commonly occurring during growth and processing of the respective heteroepitaxial ...

    SBIR Phase I 2019 Department of DefenseArmy
  4. Virtual Reality Collaboration Tool for Mission Command

    SBC: Attollo, LLC            Topic: A19039

    Attollo’s concept is to utilize our Scene Generator Technology, to develop a 3D interactive and collaborative sand table/mapping tool for use on a portable mission planning/briefing device; this device can be easily deployable. The tool provides a volumetric virtual map that is shareable and follows Army planning protocol and doctrine. Additionally, an overlaid task bar can display specifically ...

    SBIR Phase I 2019 Department of DefenseArmy
  5. Lightweight Bullet and Fragment Impact Protection for Mobile Missile Launcher

    SBC: SAFE INC            Topic: A17034

    Missile launcher armor is needed to protect propellants from unintended ignition when struck by ballistic projectiles and fragments. Allowing fragments to penetrate the armor at low speed limits the chance of ignition while lightening the armor. The closely-spaced shot pattern and thickness and weight limits still make a significant design challenge. Safe has selected materials suitable for the th ...

    SBIR Phase I 2017 Department of DefenseArmy
  6. Air Platform Passive Occupant Protection

    SBC: SAFE INC            Topic: A18001

    Body flailing during a severe helicopter crash can lead to injury or death when the head and upper torso strike rigid objects within the flail envelope.Currently fielded restraint systems allow a large flail envelope because the strap routing and anchor positions require some body motion to occur before the straps can develop significant reaction loads.Safe, Inc. (Safe) is proposing an alternate d ...

    SBIR Phase I 2018 Department of DefenseArmy
  7. Variable Pulsed Parameter Tracking Illuminator Laser

    SBC: N.P. PHOTONICS, INC.            Topic: A17104

    NP Photonics proposes to design and develop a laser source capable of producing a high energy nanosecond laser with variable parameters and short coherent length by taking advantage of our laser technologies based on highly doped glasses. Tracking illuminator lasers (TILs) have a variety of applications in weapon system engagements including target detection, target identification, pose estimation ...

    SBIR Phase I 2017 Department of DefenseArmy
  8. Near Real-Time LIDAR Processing and Exploitation Algorithm Development

    SBC: RINCON RESEARCH CORPORATION            Topic: A17143

    Todays advanced LiDAR systems typically lack the ability to autonomously detect man-made shapes and structures and provide that 3-D data to Geospatial Intelligence quickly and effectively to aid in tactical decisions. Rincon Research Corporation (RRC) presents its solution to this problem through the design and development of algorithms that perform onboard Automated Feature Extraction (AFE) and/o ...

    SBIR Phase I 2018 Department of DefenseArmy
  9. Spall Liner Energy Attenuating (EA) Material Development

    SBC: SAFE INC            Topic: A18084

    Occupants of ground combat vehicles are at risk of head injury when the vehicle is attacked by an underbody blast and its violent motion causes the head to strike the interior.Occupants are also at risk from spallfragments of material liberated from the interior wall of the vehicle by shock waves or overmatched threats.Vehicles currently have interior liner panels for spall mitigation but lack ade ...

    SBIR Phase I 2018 Department of DefenseArmy
  10. Ultra-Durable Polyolefin Based Waterproofing Coating

    SBC: RESODYN CORPORATION            Topic: A16114

    The U.S. Army is interested in the development of innovative materials, films, coatings and technologies or manufacturing techniques which allow current U.S. Army airdrop related hardware and equipment to survive fresh and salt water operations with increased reliability and without damage and significant maintenance impact. Resodyn Corporation proposes for development a durable, moisture-impermea ...

    SBIR Phase I 2017 Department of DefenseArmy
US Flag An Official Website of the United States Government