Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until September, 2020.

  1. Hermetic Seals for Chemical/Biological Protective Garments

    SBC: CREARE LLC            Topic: CBD13109

    Interfaces on existing military chemical/biological protection garments are not designed to fully eliminate macroscopic and microscopic airgaps at folds, fabric surfaces, or hook-and-loop closures, and thus do not provide a hermetic barrier against exposure. Creare is developinghermetic garment closure systems that seal macroscopic and microscopic gaps at interfaces and closures and provide high c ...

    SBIR Phase II 2018 Department of DefenseOffice for Chemical and Biological Defense
  2. Novel Methods to Measure Penetrator Dynamics in Multi-Layer Geometries

    SBC: Thornton Tomasetti, Inc.            Topic: DTRA07011

    In Phase I of this effort we analyzed the structural response of a BLU 109 during typical penetration events. Based on these finite element results, we proposed and demsonstrated a simple robust concept for a passive penetrator sensor that identifies the material being penetrated and also correlates strongly with its underground trajectory. Such a sensor would obviously provide valuable informatio ...

    SBIR Phase II 2008 Department of DefenseDefense Threat Reduction Agency
  3. The Characterization and Mitigation of Single Event Effects in Ultra-Deep Submicron (< 90nm) Microelectronics

    SBC: Orora Design Technologies, Inc.            Topic: DTRA07005

    Orora Design Technologies proposes to develop electronic design automation (EDA) tools employing minimally invasive circuit design-based methods to mitigate single event effects (SEEs) for next generation Ultra-DSM CMOS (

    SBIR Phase II 2008 Department of DefenseDefense Threat Reduction Agency
  4. Omni-Directional, Wind and Water Tolerant Inlet for the DFU

    SBC: ENERTECHNIX, INC.            Topic: CBD07116

    The current DFU inlet exhibits poor aerosol sampling efficiency at high wind speeds. This project will develop an improved inlet with very high sampling efficiency for 1 to 20 micron particles at wind speeds up to 30 mph independent of wind direction. The project is focused on the DFU, but our Aerodynamic Next Generation Inlet (ANGI) will be beneficial for any high volume aerosol sampling applicat ...

    SBIR Phase II 2008 Department of DefenseOffice for Chemical and Biological Defense
  5. Automated Objective Speech Intelligibility Assessment System

    SBC: LI Creative Technologies Inc.            Topic: CBD07106

    Based on the success of our Phase I feasibility research, we propose to continue the project for the automated objective speech intelligibility assessment system. It consists of a pair of head and torso simulators placed at the same distance as typical face-to-face communication, a power amplifier, a laptop computer, a speech recognizer, and console software. The simulator has acoustic properties ...

    SBIR Phase II 2008 Department of DefenseOffice for Chemical and Biological Defense
  6. Lightweight, Efficient Blower for Personal Air Ventilation System

    SBC: CREARE LLC            Topic: CBD07115

    A personal air ventilation system (PAVS) can dramatically improve the environment inside chemical/biological protective clothing, protecting the health and safety of soldiers and enabling peak physical/mental performance for long periods. However, existing air blowers that can produce the flow rate and pressure drop needed for a PAVS are too heavy, inefficient, and noisy for a man-portable system ...

    SBIR Phase II 2008 Department of DefenseOffice for Chemical and Biological Defense
  7. DEVELOPMENT OF A RESIDUAL IN-SITU STRESS GAUGE

    SBC: Terra Tek Inc.            Topic: N/A

    QUANTITATIVE VERIFICATION OF THE RESIDUAL IN-SITU STRESS FIELD WHICH CREATES THE CONTAINMENT CAGE IS NEEDED TO ASSESS THE FACTOR OF SAFETY AGAINST HYDRAULIC FRACTURING FROM THE CAVITY WALL. PHASE I WILL ESTABLISH THE FEASIBLITY OF DEVELOPING A PASSIVE STRESS GAUGE, ABSENT OF ACTIVE INSTRUMENTATION, AND CAPABLE OF RECORDING THE RESIDUAL IN-SITU STRESS FIELD IMMEDIATELY FOLLOWING THE NUCLEAR DEVICE ...

    SBIR Phase II 1991 Department of DefenseDefense Threat Reduction Agency
US Flag An Official Website of the United States Government