You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. A Scheme to Reduce Dark Current in SLS FPAs

    SBC: QMAGIQ LLC            Topic: MDA11005

    Longwave infrared focal plane arrays (FPAs) based on Type-II InAs/GaSb-based strained layer superlattice (SLS) photodiodes show good performance at the current time. A key remaining challenge is the reduction of dark current, dominated by pixel surface leakage in FPAs and low minority carrier lifetime in the bulk material. We propose to address the former in this Phase I and develop a unique sche ...

    SBIR Phase I 2012 Department of DefenseMissile Defense Agency
  2. Optimized Thermal Battery for Weight- and Size-Constrained Applications

    SBC: Erigo Technologies LLC            Topic: MDA10018

    Thermal batteries are a power source for most MDA weapons systems. Some of these applications place severe constraints on battery weight and size. The key components of thermal batteries are typically made by hydraulically pressing powders into"pellets". The pellets must be greater than a minimum thickness to avoid breakage, and for batteries that must supply high current for a short time this ...

    SBIR Phase II 2012 Department of DefenseMissile Defense Agency
  3. 640x512 Dualband Longwave/Longwave Infrared SLS FPA For Interceptor Seekers

    SBC: QMAGIQ LLC            Topic: MDA10012

    In Phase I we developed a novel infrared photodiode based on Type-II InAs/GaSb strained layer superlattices (SLS) that showed pingpong dualband action, wherein the spectral response of the diode was switched between extended midwave (~ 8 micron cutoff) and longwave (~ 10 micron cutoff) infrared by the polarity of the voltage bias applied across it. In Phase II we will improve quantum efficiency i ...

    SBIR Phase II 2012 Department of DefenseMissile Defense Agency
  4. Small Integrated HFI Sensor for the AVR-2B

    SBC: SOLID STATE SCIENTIFIC CORPORATION            Topic: SOCOM11001

    "SSSC is pleased to propose the development and delivery of a Hostile Fire Indication Sensor (HFIS) based on the Phase I design concept. The resulting system will limit the number of circuit card assemblies to two: one for the short wave infrared (SWIR)

    SBIR Phase II 2012 Department of DefenseSpecial Operations Command
  5. Development of enhanced active damping system for the Marine Corps Expeditionary Fighting Vehicle (EFV)

    SBC: ACTIVE SHOCK, INC.            Topic: N04192

    A road wheel suspension incorporating a semi-active damper and fast load leveling spring system will be developed for the Expeditionary Fighting Vehicle (EFV). The system will be designed as a replacement for the currently fielded semi-active suspension system in the same foot print, either in early production units or as a retrofit package for incorporation later in the development cycle. A sus ...

    SBIR Phase I 2005 Department of DefenseSpecial Operations Command
  6. Innovative Techniques for Missile Defense- Proportional Hot Gas Actuator for DACS

    SBC: APPLIED THERMAL SCIENCES            Topic: MDA04020

    A key component of missile interceptor vehicles is the divert and attitude control system (DACS), which is responsible for maneuvering the interceptor vehicle to its target. A vital component to the DACS is the thruster, which provides effective control of vehicle divert. Solid propellant DACS thrusters employ an adjustable pintle for controlling the thrust level. Movement of the pintle for smo ...

    SBIR Phase II 2005 Department of DefenseMissile Defense Agency
  7. Design Development of an Advanced Composite Interceptor Nosecone for KEI

    SBC: Fiber Materials, Inc.            Topic: MDA04111

    The proposed nosecone development effort will investigate application of the following component technologies to a ground base interceptor deployable nosecone for KEI: [1] an advanced ceramic resin matrix for the thermal protection system, [2] a low-shock nosecone separation system, [3] a lightweight composite assembly configuration and [4] integration of lightning/EMI shielding into the composite ...

    SBIR Phase I 2005 Department of DefenseMissile Defense Agency
  8. Multi-Dimensional Reinforced Ceramic Matrix Composite Application to Advanced Pintle Operated DACS Systems

    SBC: Fiber Materials, Inc.            Topic: MDA04111

    This program proposes to investigate and demonstrate novel composite material concepts for advanced divert and attitude control solid propulsion systems. Fiber Materials Inc. (FMI) teamed with ATK Elkton LLC, proposes to develop multi-directional reinforced ceramic matrix composite (CMC) material applicable to ATK's Block II SDACS, KEI, MKV, advanced PBCS and advanced Patriot reaction control sys ...

    SBIR Phase I 2005 Department of DefenseMissile Defense Agency
  9. Integrated Missile Harness-Fairing Assembly

    SBC: Fiber Materials, Inc.            Topic: MDA04111

    A need exists for a state-of-the-art electrical interconnection assembly that will simplify missile manufacture and assembly at a reduced cost relative to current methods. It should provide thermal protection, facilitate internal individual EMI shielding from each bundle type as well as external sources, and minimize the harness-fairing profile reducing aerodynamic forces. Fiber Materials, Inc. ( ...

    SBIR Phase I 2005 Department of DefenseMissile Defense Agency
  10. Innovative Manufacturing Process Improvements

    SBC: MENTIS SCIENCES INC            Topic: MDA04035

    The projected cost for the Mentis Sciences, Inc., (MSI) prototype PAC3 radome is 1/6th of the total cost of the present system. A Pareto analysis of the current MSI process indicates that the two largest costs in radome production are the direct labor associated with fabrication and the cost of the raw materials. In Phase I MSI demonstrated that COTS paint spraying technology reduced the direct ...

    SBIR Phase II 2005 Department of DefenseMissile Defense Agency
US Flag An Official Website of the United States Government