You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Production of Chemical Reagents for Prompt-Agent-Defeat Weapons

    SBC: Nalas Engineering Services Inc            Topic: DTRA14B001

    Nalas Engineering and Johns Hopkins University collaborated in a Phase I STTR program to study reactive mixtures of HI3O8 and nanocomposite fuels previously developed by the Weihs Group. These fuel/oxidizer mixtures are uniquely able to simultaneously produce heat and biocidal iodine gas, a combination designed to destroy biological weapons. The team at Nalas focused on evaluating conditions for p ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  2. Semantic Parsing and role Labeling In Combination Effort (SPLICE)

    SBC: DECISIVE ANALYTICS CORPORATION            Topic: DTRA14B003

    To Counter Weapons of Mass Destruction (CWMD), DTRA must analyze data from numerous sources about a diverse set of technologies and activities. The extreme diversity in content and the volume of DTRAs data combine to produce one of the most challenging analysis problems in the government. The CWMD mission therefore requires deep analysis - an in-depth understanding of all available data and correl ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  3. Portable System with Li Foil MWPC Neutron Detectors

    SBC: Radiation Detection Technologies, Inc.            Topic: DTRA14B005

    At the completion of the research and development effort a Li-foil multi-wire proportional counter (MWPC) neutron detector with more than 625-cm2 of active area will be included in a portable radiation detection system. The system is expected to outperform the standards set by the ANSI N42.53 standards, and gamma-ray rejection ratio (GRR) of 1.0x10-8 or better. A gamma-ray spectrometer for isotope ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  4. Innovative Wound Regeneration Support Approaches to Enable Rapid Treatment of Wounded Warfighters

    SBC: Zetroz Systems LLC            Topic: A14AT016

    Ultrasound is a therapeutic modality which has been used clinically for 60 years, but has been limited in practice by the complexity of the technology. Recent research has allowed for the development of a portable, wearable, long duration, low intensity therapeutic ultrasound system. The system is powered by battery, and can be applied by a user to deliver up

    STTR Phase II 2016 Department of DefenseDefense Health Agency
  5. Interactive Mixed Media Education augmented Reality Simulation Engine (IMMERSE)

    SBC: CHI Systems, Inc.            Topic: DHA17A003

    CHI Systems, in partnership with the Virginia Serious Games Institute, proposes to design, develop, and assess the Interactive Mixed Media augmented Reality Simulation Engine (IMMERSE) technology, a compelling and instructionally rich training experience using augmented and mixed-reality for TC3 trainees, and then evaluate the impact of the IMMERSE approach on trainee understanding and training ef ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  6. Developing Software for Pharmacodynamics and Bioassay Studies

    SBC: TConneX Inc.            Topic: DHP16C001

    Estimation of the primary parameters like IC 50 in traditional dose-response modelsmay fail or lead to misleading results when the observations are non-onotonic due to drugresistance or virus mutation in various biomedical lab research. The objective of this project isto develop a novel approach to assess dose response relationship, which is applicable to generalpharmacologic, toxicologic, or othe ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  7. Ultra-Wide Band RF Quantitative Diagnostics of Burn Injuries

    SBC: NOKOMIS, INC            Topic: DHP16C005

    This proposal is dedicated to development of portable device for -on site- diagnostic of burn injury. The design will utilize a technology Ultra-Wide Band RF waves of ultra-low intensity (harmless by Federal Standards). The emitted RF waves will reflect from boundaries between tissues normal and damaged by injury to quantitatively characterize severity of burn and would require minimal skills fro ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  8. Smart Morphing Moulage Medical (SM3) Training Platform

    SBC: Luna Innovations Incorporated            Topic: DHA17A002

    Medical moulage is used in medical training to simulate injuries or pathologies, however current moulage is static and does not provide the trainee feedback on the quality of care or ultimate outcome of that care. Allowing a trainee to witness the injury or pathology -morph- while treatment is being provided can provide feedback on any potential mistreatment and enhance the learning and proficienc ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  9. VOC Breath Analysis with Ultra-Sensitive Microwave Spectroscopy

    SBC: NOKOMIS, INC            Topic: DHP16C002

    Nokomis proposes to develop a real-time microwave spectroscopy device to identify Volatile Organic Compounds (VOCs) associated with Pulmonary Oxygen Toxicity. Exhaled breath contains VOCs that act as signatures of bodily health, and are able to be utilized for health diagnostics. The proposed work will demonstrate sensitivity to the presence of chemicals at less than 50 ppb concentration levels, a ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  10. Rapid Development of Weapon Payloads via Additive Manufacturing

    SBC: Matsys Incorporated            Topic: DTRA16A001

    MATSYS proposes to adapt emerging additive manufacturing techniques (so-called 3-D Printing) for use with reactive structural materials and demonstrate this capability to rapidly fabricate reactive case. Our concept incorporates two major manufacturing steps: 3D printing of green compacts from pure Al or Al-based reactive powder blend; and Microwave (MW) sintering of green compacts into net-shaped ...

    STTR Phase I 2016 Department of DefenseDefense Threat Reduction Agency
US Flag An Official Website of the United States Government