You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY22 is not expected to be complete until September, 2023.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Discrete 3-D Electronics for Mobile Radiation Detection Systems

    SBC: Radiation Detection Technologies, Inc.            Topic: DTRA18B002

    Phase II will utilize knowledge gained from phase I work to develop and execute a manufacturing process suitable for producing quantities of 3-D printed discrete circuits for radiation detection systems.  The goal is to support mobile radiation detection system requirements for high voltage, analog amplification, and MCA functionality to produce differential pulse height spectra in time sequence. ...

    STTR Phase II 2020 Department of DefenseDefense Threat Reduction Agency
  2. Urbanscape: Single Shot Multi-Task 3D Reconstruction

    SBC: Dzyne Technologies Incorporated            Topic: DTRA18B001

    Hazard assessment tools that model the transport and dispersion of Chemical, Biological, Radiological, Nuclear and Explosive (CBRNE) materials through urban areas are only as good as the 3D models that inform the physics model. Maintaining accurate, up-to-date 3D models of urban areas is challenging. Even in the commercial world, urban construction and demolition may result in the models created a ...

    STTR Phase II 2020 Department of DefenseDefense Threat Reduction Agency
  3. Hardened, Optically-Based Temperature Characterization of Detonation Environments

    SBC: SA Photonics, Inc.            Topic: DTRA19B001

    Improving the effectiveness of counter-WMD operations requires improved understanding of weapon-target interaction. Specifically, time-resolved measurements of temperature and composition are required to allow temporal evolution of a detonation fireball. To address this need, SA Photonics will develop MONITOR, a laser-based temperature diagnostic that will enable wide dynamic range temperature mea ...

    STTR Phase I 2020 Department of DefenseDefense Threat Reduction Agency
  4. Improved Identification of the function of Novel and Partially Occluded Laboratory Equipment.

    SBC: Novateur Research Solutions, LLC            Topic: DTRA19B002

    This STTR Phase 1 project proposes development of a statistical relational learning framework for identification of the function of laboratory equipment from imagery. The proposed framework uses semantic reasoning to incorporate evidence from multiple classifiers and feature extractors, domain knowledge, and scene context for scene understanding and labeling. The Phase I effort will focus on imple ...

    STTR Phase I 2020 Department of DefenseDefense Threat Reduction Agency
  5. Production of Chemical Reagents for Prompt-Agent-Defeat Weapons

    SBC: Nalas Engineering Services Inc            Topic: DTRA14B001

    Nalas Engineering and Johns Hopkins University collaborated in a Phase I STTR program to study reactive mixtures of HI3O8 and nanocomposite fuels previously developed by the Weihs Group. These fuel/oxidizer mixtures are uniquely able to simultaneously produce heat and biocidal iodine gas, a combination designed to destroy biological weapons. The team at Nalas focused on evaluating conditions for p ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  6. Semantic Parsing and role Labeling In Combination Effort (SPLICE)

    SBC: DECISIVE ANALYTICS CORPORATION            Topic: DTRA14B003

    To Counter Weapons of Mass Destruction (CWMD), DTRA must analyze data from numerous sources about a diverse set of technologies and activities. The extreme diversity in content and the volume of DTRAs data combine to produce one of the most challenging analysis problems in the government. The CWMD mission therefore requires deep analysis - an in-depth understanding of all available data and correl ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  7. Portable System with Li Foil MWPC Neutron Detectors

    SBC: Radiation Detection Technologies, Inc.            Topic: DTRA14B005

    At the completion of the research and development effort a Li-foil multi-wire proportional counter (MWPC) neutron detector with more than 625-cm2 of active area will be included in a portable radiation detection system. The system is expected to outperform the standards set by the ANSI N42.53 standards, and gamma-ray rejection ratio (GRR) of 1.0x10-8 or better. A gamma-ray spectrometer for isotope ...

    STTR Phase II 2017 Department of DefenseDefense Threat Reduction Agency
  8. Development of powder bed printing (3DP) for rapid and flexible fabrication of energetic material payloads and munitions

    SBC: MAKEL ENGINEERING INC            Topic: DTRA16A001

    This program will demonstrate how additive manufacturing technologies can be used with reactive and high energy materials to create rapid and flexible fabrication of payload and munitions. Our primary approach to this problem will be to use powder bed binder printing techniques to print reactive structures. The anticipated feedstock will consist of composite particles containing all reactant spe ...

    STTR Phase I 2016 Department of DefenseDefense Threat Reduction Agency
  9. Innovative Mitigation of Radiation Effects in Advanced Technology Nodes

    SBC: RELIABLE MICROSYSTEMS LLC            Topic: DTRA16A003

    Establish a radiation-aware analysis capability in a commercial EDA design flow that will enable first-pass success in radiation-hardened by design (RHBD) for DoD ASICs in much the same way that existing EDA design suites ensure first pass functionality and performance success of complex ASICs destined for commercial applications. Layout-aware, calibrated single-event radiation models that captur ...

    STTR Phase I 2016 Department of DefenseDefense Threat Reduction Agency
  10. Rapid Development of Weapon Payloads via Additive Manufacturing

    SBC: MATSYS INC            Topic: DTRA16A001

    MATSYS proposes to adapt emerging additive manufacturing techniques (so-called 3-D Printing) for use with reactive structural materials and demonstrate this capability to rapidly fabricate reactive case. Our concept incorporates two major manufacturing steps: 3D printing of green compacts from pure Al or Al-based reactive powder blend; and Microwave (MW) sintering of green compacts into net-shaped ...

    STTR Phase I 2016 Department of DefenseDefense Threat Reduction Agency
US Flag An Official Website of the United States Government