Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Colorimetric Monitoring of Trace Toxic Air Pollutants

    SBC: ChemSensing, Inc.            Topic: N/A

    One of the program areas of interest to the U.S. Environmental Protection Agency (EPA) is the development of rapid, non-invasive monitors to detect exposure to toxic air pollutants at trace (ppt) levels. Of the 356 chemicals listed on the Chemical Emergency Preparedness and Prevention Office¿s List of Extremely Hazardous Substances (Section 302 of the Emergency Planning and Community Right-To-Kn ...

    SBIR Phase I 2003 Environmental Protection Agency
  2. SYSTEM OF CONTINUOUS EXTENSIVE MONITORING OF DRINKING, NATURAL AND INDUSTRIAL WATERS

    SBC: ECI TECHNOLOGY, INC.            Topic: N/A

    N/A

    SBIR Phase I 1994 Environmental Protection Agency
  3. Near-Zero VOC General OEM Bake Enamel

    SBC: Finishes Unlimited, Inc.            Topic: N/A

    Finishes Unlimited, Inc., produces baking enamels for general purpose original equipment manufacturers who make sundry metal products such as lockers, tool boxes, compressors, folding chairs, storage racks, etc. Although it is a small company, Finishes Unlimited, Inc., has been among the leaders in one type of environmentally friendly coatings (i.e., waterborne bake enamels). In 1993, it became ...

    SBIR Phase I 2003 Environmental Protection Agency
  4. SCRAP TIRE PYROLYSIS-- PRODUCTION OF HIGHLY ENHANCED MARKETABLE PRODUCTS

    SBC: Hichem Corp.            Topic: N/A

    RESEARCH WILL BE CONDUCTED BY HICHEM CORPORATION, TO DEVELOP A NEW TECHNOLOGY FOR PYROLYSIS OF SCRAP TIRES. DISPOSAL OF USED TIRES IS A BIG PROBLEM IN THE WORLD, ESPECIALLY USA, SINCE MORE THAN 2.5 MILLION TIRES ARE DISCARDED EACH YEAR. MOST OF THESE TIRES ARE DISPOSED IN LANDFILLS. PYROLYSIS OF SCRAP TIRES HELPS TO RECOVER AND REUSE MOST OF THE VALUABLE CHEMICAL AVAILABLE IN TIRES. PYROLYSIS OF S ...

    SBIR Phase II 1994 Environmental Protection Agency
  5. IMPROVED METHOD FOR HEATING CATALYTIC CONVERTERS OF VEHICLES TO ATTAIN ULTRA-LOW EMISSIONS

    SBC: Lynntech Inc.            Topic: N/A

    THE THREE-WAY CATALYTIC CONVERTER IS THE MOST IMPORTANT DEVICE MAKING TODAY'S AUTOMOBILES COMPLY WITH EXISTING EMISSION LAWS. THE FIRST TWO OR THREE MILES IN A TYPICAL 22-MINUTE, 12-MILE COMUTE IN TODAY'S VEHICLES RESULT IN THE EMISSION OF HALF OF THE TOTAL NON-METHANE HYDROCARBONS, WHICH RESULT IN THE PRODUCTION OF URBAN SMOG, AS WELL AS HALF OF THE TOXIC CO EMISSIONS. THIS OCCURS BECAUSE THE CAT ...

    SBIR Phase II 1994 Environmental Protection Agency
  6. A CONTINUOUS EMISSION MONITORING DEVICE FOR AIRBORNE METALS

    SBC: OPTOMECHANICAL ENTERPRISES, INC.            Topic: N/A

    N/A

    SBIR Phase I 1994 Environmental Protection Agency
  7. Novel Method for DBP Precursor Removal

    SBC: Universal Fuel Development            Topic: N/A

    N/A

    SBIR Phase I 1994 Environmental Protection Agency
  8. Upflow Filters for the Rapid and Effective Treatment of Stormwater at Critical Source Areas

    SBC: USInfrastructure, Inc.            Topic: N/A

    This research project is designed to develop and demonstrate the effectiveness of upflow filtration setups for the treatment of stormwater runoff. To show improvement in water quality in many urban areas, it will be necessary to either collect the stormwater runoff in a central location and treat it, or install and maintain many small treatment devices throughout the area. USInfrastructure¿s ...

    SBIR Phase I 2003 Environmental Protection Agency
  9. Repair of HighTemperature RAM Coatings

    SBC: WELLS SIGNATURE PRODUCTS LLC            Topic: N/A

    A coating system is proposed comprised of1. Gradient pigment particles having an iron core encapsulated with a mixed intermetallic-oxide layer and a further silicon-based layer for enhanced bonding to the matrix2. A matrix raw material that is thermally-sprayable using conventional technology that partially cures to an oxide during application and becomes fully cured on first use3. Thermal spray e ...

    SBIR Phase I 2003 Department of DefenseAir Force
  10. Advanced Aluminum Alloy: Extruded Thin Wall Structural Concepts

    SBC: Advanced Technologies/Laboratories Intl            Topic: N/A

    The primary objective of this proposed work is to develop a method of producing integrally stiffened, complex shaped monolithic structural components in high strength aluminum alloys at a lower cost and lighter weight than equivalent conventional built-up assemblies. In Phase I the feasibility of attaining this objective will be demonstrated by conducting a series of subscale experiments based upo ...

    SBIR Phase I 1994 Department of DefenseAir Force
US Flag An Official Website of the United States Government