You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. Innovative improvements to High-Frequency Simulation Methods for Installed Antenna Performance

    SBC: DELCROSS TECHNOLOGIES, LLC            Topic: N103197

    Delcross proposes to systematically validate the Savant and Savant-Hybrid ray tracing solvers for a wide variety of installed antenna configurations, including far-field patterns, near-field distributions, and antenna-to-antenna coupling. Reference benchmarks will be developed from full-wave solvers, measurements, and analytic solutions. When shortcomings in existing methods/algorithms are identif ...

    SBIR Phase II 2011 Department of DefenseNavy
  2. Insert ear-probe assembly for high-quality otoacoustic-emission (OAE) measurements in adults

    SBC: Mimosa Acoustics Inc.            Topic: N10AT032

    OAE has proved to be an important measurement for hearing conservation programs. OAEs are sounds made by healthy inner ears in response to acoustic stimulation and are measured in the ear canal with a miniature microphone. One impediment to OAE testing on a large scale, such as in military hearing conservation programs, is the lack of a high-quality, reliable ear-probes which house the miniature m ...

    STTR Phase II 2011 Department of DefenseNavy
  3. Radio Frequency (RF) System Performance and Electromagnetic Interference (EMI) in Dynamic Environments

    SBC: DELCROSS TECHNOLOGIES, LLC            Topic: N103202

    For manned and unmanned vehicles in current military operating environments, many adversary and civilian platforms exist that can be considered non-traditional, unconventional, or otherwise unaccounted for in the design of these vehicles. These unconventional and nontraditional aircraft, ship, and boat targets pose unique challenges to radar system designers, analysts, and operators. To aid in the ...

    SBIR Phase II 2011 Department of DefenseNavy
  4. Development of Electronic Controlled Fuel Injector and Pump Suitable for 5-20 Horsepower Diesel Cycle Engines

    SBC: KINETIC BEI LLC            Topic: N10AT033

    Phase II will enable KBEI to demonstrate a complete high pressure Micro Injection System on a Navy UAV engine in a laboratory environment. While the Micro Injectors and Micro Pump have been successfully proven at lower pressures, this STTR program has facilitated research and development of a higher pressure injection system designed for use with heavy fuels. At the conclusion of the Phase II ST ...

    STTR Phase II 2011 Department of DefenseNavy
  5. Development of a Scalable, Low-Cost, Ultrananocrystalline Diamond Electrochemical Process for the Destruction of Contaminants of Emerging Concern (CECs)

    SBC: Advanced Diamond TechNologies, Inc.            Topic: E

    This Small Business Innovation Research (SBIR) project will develop and ready for commercialization a scalable, low-cost process for purification of water containing Contaminants of Emerging Concern (CECs) using anodic oxidation with boron-doped ultrananocrystalline diamond (UNCD®) thin films. Resent research demonstrated that there is considerable potential for the development of electrochemica ...

    SBIR Phase I 2011 Environmental Protection Agency
  6. L-(+) Lactic Acid Production from Biodiesel Waste Using Pelletized Fungal Fermentation

    SBC: OMNILANE, INC.            Topic: H

    "With the rapid growth of biodiesel industry, the production of crude glycerol as one of major biodiesel byproducts has been dramatically increased. Fully utilizing such a large quantity of crude glycerol is critical to the sustainability of biodiesel industry. Lactic acid is an important industrial chemical that is widely used as a food additive for flavoring and preservative, a moistener in co ...

    SBIR Phase I 2011 Environmental Protection Agency
  7. High Voltage, Lightweight, Conformal, Integrated, Photovoltaic Modules for Unmanned Aerial Vehicles (UAVs)

    SBC: Microlink Devices, Inc.            Topic: N10BT048

    MicroLink proposes a novel device structure which combines ultra-thin, high-efficiency, GaAs-based multijunction solar cells with a novel packaging approach that will result in high flexibility, elastic solar sheets. MicroLink has developed a process that produces ultra-thin, flexible solar cells. In this project, these an array of these flexible solar cells will be incorporated onto an elastic sh ...

    STTR Phase I 2011 Department of DefenseNavy
  8. Safe High Voltage Cathode Materials for Pulsed Power Applications

    SBC: Engi-Mat Co.            Topic: N11AT035

    nGimat & Oak Ridge National Labs jointly propose to develop safe high-voltage cathode materials for pulsed power applications in the military and commercial sectors. nGimat's versatile NanoSpray Combustion process will be utilized to tailor the bulk & surface composition of the cathode materials as well as the particle size & morphology to meet the demanding energy, power and safety requirem ...

    STTR Phase I 2011 Department of DefenseNavy
  9. High Strength Stress Corrosion Resistant Aluminum Casting Alloys

    SBC: QUESTEK INNOVATIONS LLC            Topic: N102106

    The United States Marine Corps (USMC) is pursuing high-performance aluminum castings for structural components of the Expeditionary Fighting Vehicle (EFV). Aluminum alloy A206 has been considered for these applications; however, this alloy is susceptible to hot tearing during casting, and has inferior stress-corrosion cracking (SCC) resistance. Under this proposed SBIR program, QuesTek Innovations ...

    SBIR Phase I 2011 Department of DefenseNavy
  10. High Strength Stress Corrosion Resistant Aluminum Casting Alloys

    SBC: ATI, INC.            Topic: N102106

    The approach selected to address the development of High Strength Stress Corrosion Resistant Aluminum Casting Alloys is to use A201 and AA2139 as the base alloy and modify/optimize the composition use thermodynamic modeling . Reducing the susceptibility to hot-tearing will be achieved through the use incorporation of grain refiners such as dispersoid forming elements to control the dispersoid/dend ...

    SBIR Phase I 2011 Department of DefenseNavy
US Flag An Official Website of the United States Government