Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Hierarchical Grid Referenced Normalized Display (HiGRND)

    SBC: 21ST CENTURY SYSTEMS, INC.            Topic: HSB062005

    In an Urban Search and Rescue (USAR) scenario, the ability for the rescuers to maintain an accurate and comprehensive situational awareness is critical to allow them to maximize their effectiveness in a chaotic and dangerous environment. Timeliness is, of course, paramount to saving lives, and miscommunications lead to potentially unnecessary deaths. 21st Century Systems Incorporated is pleased to ...

    SBIR Phase I 2006 Department of Homeland Security
  2. High Quantum Efficiency Fast Detectors for Readout of Scintillators for Gamma Ray Detection

    SBC: VOXTEL, INC.            Topic: HSB062007

    High quantum efficiency (QE), fast (

    SBIR Phase I 2006 Department of Homeland Security
  3. NANOFIBER NONWOVEN BASED AIRCREW PERSONNEL LOWERING DEVICE

    SBC: 3F, LLC            Topic: AF06020

    Nanofiber nonwoven spunbonded materials technology is adapted for use in a personnel lowering device. The resulting device will be simple, easy to use, and relatively low cost.

    SBIR Phase I 2006 Department of DefenseAir Force
  4. Low-Output High Precision Automated Powder Disseminator

    SBC: ADVANCED MECHANICAL SYSTEMS TECHNOLOGY,            Topic: CBD06101

    This proposal presents a Phase I SBIR project to develop a high precision, low disperse rate powder disseminator for the US Army. In the development of the sensitive detecting agent, we need to release a precise amount of C&B agents in the controlled detection experiments. However, such a technology does not exist at the present time. After examining existing technologies, we believe that the r ...

    SBIR Phase I 2006 Department of DefenseOffice for Chemical and Biological Defense
  5. Single ply 3Dwoven Functionally Gradient Multi-Fiber / Multi-Matrix Composites with Thermal Management Systems

    SBC: 3TEX, Inc.            Topic: AF04249

    In composites, not only can properties vary with load direction, fiber based composites also offer the unique ability to tailor material properties locally. Localized matrix or fiber architecture changes can meet local mechanical, electrical, or thermal loads within a component or vehicle, without weight penalty or resort to additional external structures. In Phase I, the team used 3TEX 3-D wea ...

    SBIR Phase II 2006 Department of DefenseAir Force
  6. Integrally 3D Woven/3D Braided Composite Joining Elements For Ship Construction

    SBC: 3TEX, Inc.            Topic: N04093

    During Phase I, 3TEX designed universal, one-piece, 3D woven fiber preforms which can be used as either a “Butt” (H) joint or as a “P” joint as needed. Composite joints were fabricated and tested, demonstrating the benefit of the integral nature of the 3D preforms. 3D stress/strain and crack propagation analysis of composite Π-joint was performed using 3D MOSAIC code. 3D displacement, st ...

    SBIR Phase II 2006 Department of DefenseNavy
  7. Novel Structural Joining Concepts Using 3-D Textile Preforms and Composites

    SBC: 3TEX, Inc.            Topic: AF05248

    Strength and durability of commonly used bonded and bolted composite-to-composite and composite-to-metal structural joints suffer from sharp geometry variations, mismatch of elastic moduli, Poisson’s ratios, coefficients of thermal expansion and thermal conductivity of the adherends, altogether causing high stress concentration and premature joint failure. The proposed work is focused on develop ...

    SBIR Phase II 2006 Department of DefenseAir Force
  8. 3-D Fiber Reinforced, Thermally Conductive Rotor Sheaths

    SBC: 3TEX, Inc.            Topic: N06T013

    Military helicopters rotors contend with rain, ice, sand, and flying debris. To prevent damage to the expensive blade protective sheaths or coatings are applied to the leading edge of the rotor blades. A 3-D woven composite sheath with high thermal conductivity fibers running through the thickness can offer the best qualities of both metal sheaths and elastomer coatings. Infused with an elastom ...

    STTR Phase I 2006 Department of DefenseNavy
  9. Improved Miller Fasteners Based on 3-D Braided Preforms

    SBC: 3TEX, Inc.            Topic: N06033

    Miller Fasteners made from 2-D laminates represent the state of the art in joining CMC panels to metal frames. Despite its success, the extant Miller fastener design is limited by its construction from a laminate of 2-D fabric. The resultant fastener part has poor interlaminar shear strength, and its manufacture and application entails high machining costs and high material scrap rates. 3TEX, i ...

    SBIR Phase I 2006 Department of DefenseNavy
  10. Ambient Power Supply for On-Board Vehicle Health Monitoring MEMS Sensors

    SBC: AMBIENT MICRO            Topic: AF06170

    To support its use of MEMS sensors for vehicle health monitoring, the Air Force seeks to couple the harvesting of ambient energy sources with a micro energy storage device. Microbatteries have demonstrated their viability as a high density power source, but their short operating life limits their usefulness. To extend the operating life of microbatteries, ambient energy sources can be used to co ...

    SBIR Phase I 2006 Department of DefenseAir Force
US Flag An Official Website of the United States Government