You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY23 is not expected to be complete until September, 2024.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Modular Addressable Research Irradiator using Flat Panel X-ray Sources

    SBC: STELLARRAY INC            Topic: 02b

    "The National Academy of Sciences issued a report in February 2008 detailing isotope replacement priorities in the interests of national security [National Research Council, 2008] . 137Cs used in “self-contained” irradiators was identified as the single most dangerous isotope in the inventory, owing to its long half life 30+ years) and production as cesium chloride salt, which me ...

    SBIR Phase II 2015 Department of Energy
  2. Transmission Incipient Detection & Fault Location- TID&FL

    SBC: UNDERGROUND SYSTEMS INC            Topic: 22a

    In order to optimize the operating efficiency of transmission systems utilities must be able to quickly restore service after a failure. Locating faults with current technologies can be a time consuming, skill and labor intensive process. Underground transmission systems are hidden from view and fault location can take sometimes days or weeks. Detecting and locating incipient faults prior to fail ...

    SBIR Phase II 2015 Department of Energy
  3. Web-Based Computational Model Builder for Nuclear Energy Advanced Modeling and Simulation

    SBC: KITWARE INC            Topic: 19d

    According to the World Nuclear Association, the U.S. is the largest producer of nuclear power worldwide. In fact, the U.S. provides over 30 percent of the worlds nuclear generation of electricity. Although few new reactors have been built in the past 30 years, the association anticipates that four to six reactors may be built by 2020. The first of the reactors will be built in response to 16 licen ...

    SBIR Phase II 2015 Department of Energy
  4. An Additive Manufacturing Technology for the Fabrication and Characterization of Nuclear Reactor Fuel

    SBC: FREE FORM FIBERS L.L.C.            Topic: 19b

    Phase I of this Small Business Innovation Research (SBIR) project was conducted under Department of Energy's (DOE) Advanced Technologies for Nuclear Energy (NE) topic 19(b), entitled Advanced Technologies for the Fabrication, Characterization of Nuclear Reactor Fuel. Phase II preserves the two-pronged vision and goals outlined in Phase I. First, this project seeks to provide a technological a ...

    SBIR Phase II 2015 Department of Energy
  5. A High Efficiency, High Power Density, GaN-Based DC-DC Converter for Grid-Tied Energy Storage Applications

    SBC: Arkansas Power Electronics International, Inc.            Topic: 01b

    Power generation and transmission limits manifest themselves in the inability to respond to dynamic peak power demand. Load leveling can effectively support dynamic demand changes by having additional standby power generating capabilities. This is achieved by either having a generation and distribution infrastructure that matches the peak demand and it is operated under its full capacity or having ...

    SBIR Phase II 2015 Department of Energy
  6. A Hybrid HTS/LTS Superconductor Design For High-Field Accelerator Magnets

    SBC: PARTICLE BEAM LASERS, INC.            Topic: 33b

    Proposed designs for a Future Circular Collider (FCC) to collide protons with a center-of-mass energy of 100 TeV call for dipoles with fields up to 20 Tesla (T). This is significantly beyond the present technology and requires using High Temperature Superconductors (HTS). The recent Particle Physics Project Prioritization Panel (P5), organized by the U.S. Department of Energy (DOE), strongly supp ...

    STTR Phase II 2015 Department of Energy
  7. Automated Simulation Of Selective Laser Melting Additive Manufacturing For Process Design

    SBC: SIMMETRIX, INC.            Topic: 02a

    Additive Manufacturing (AM), where three-dimensional (3D) objects are created from a digital model by depositing and fusing successive layers of material, provides the ability to produce low-volume, customized products with complex geometries relatively quickly at a moderate cost. However, AM processes sometimes fail to produce acceptable parts, due to either geometric in- accuracy (e.g., shrinkag ...

    STTR Phase II 2015 Department of Energy
  8. Selective Catalysis for One-Step Lignocellulose Delignification and Lignin Valorization to High Value Methoxyphenols

    SBC: Spero Energy, Inc.            Topic: 12a

    The U.S.s global leadership position in the manufacture of high value chemicals (HVCs) relies on its ability to produce and utilize simple and useful organic (SUO) building block chemicals, a $400 billion a year enterprise based on nonrenewable petroleum feedstock. To maintain U.S.s leadership position in the 21st century, we must seek alternate renewable and economically competitive sources for m ...

    SBIR Phase II 2015 Department of Energy
  9. SpectroCCD X-ray Camera for energy dispersive spectrometers

    SBC: Sydor Instruments, LLC            Topic: 03d

    Worldwide there are a number of synchrotron beamlines dedicated to resonant soft x-ray inelastic scattering. There are also new beamlines currently being designed to take advantage of improved third generation synchrotron radiation sources and this powerful experimental technique for probing electronic structure. These beamlines utilize energy dispersive spectrometers and share a common need for a ...

    SBIR Phase II 2015 Department of Energy
  10. High Resolution Diffraction Imaging of Natural Fracture Zones in Unconventional Shale Reservoirs for Well Placement Optimization

    SBC: Z-Terra Inc.            Topic: 15c

    Accounting for the geologic conditions in unconventional shales is an important factor in an optimization problem. Placing the wells too close wastes drilling money. Placing the wells too far leaves resources in the ground. Given the fact that a well in unconventional shales may cost $12-20 million, optimizing the well placement of hundreds of wells in a field becomes a very large cost savings and ...

    SBIR Phase II 2015 Department of Energy
US Flag An Official Website of the United States Government