You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. Resistant Coatings for Aircraft Components

    SBC: ACREE TECHNOLOGIES INCORPORATED            Topic: N04261

    The purpose of this project is to demonstrate the effectiveness of using specialized protective coatings for reducing the amount of wear on aircraft components, thereby extending their life. The goal is to extend their life by a factor of 10x.

    SBIR Phase II 2006 Department of DefenseNavy
  2. Development of HFPB Debris Throw Models for Ordnance Storage and Handling Facilities

    SBC: ACTA, LLC            Topic: N06048

    Phase I showed the feasibility of developing of HFPB Debris Throw Models for Ordnance Storage and Handling Facilities using the Material Point Method (MPM) as implemented in Los Alamos' CartaBlanca code. In Phase II, a version of CartaBlanca will be installed on the Navy's supercomputer and be validated to simulate the debris thrown from a reinforced concrete (R/C) structure due to an uncased int ...

    SBIR Phase II 2006 Department of DefenseNavy
  3. Wing and Bomb Bay Launched (WBBL) Unmanned Air Vehicle (UAV)

    SBC: ACUITY TECHNOLOGIES, INC.            Topic: N05005

    The goal of the Acuity Wing and Bomb Bay Launched UAV Phase II program is demonstration of the feasibility and utility of an air vehicle organic to the P3 through development and flight testing of a prototype aircraft. Minimum objectives are runway takeoff, autonomous flight directed by a ground or air based control station through multiple waypoints over a radius of 10 miles or more, live video a ...

    SBIR Phase II 2006 Department of DefenseNavy
  4. Integrally 3D Woven/3D Braided Composite Joining Elements For Ship Construction

    SBC: 3TEX, Inc.            Topic: N04093

    During Phase I, 3TEX designed universal, one-piece, 3D woven fiber preforms which can be used as either a “Butt” (H) joint or as a “P” joint as needed. Composite joints were fabricated and tested, demonstrating the benefit of the integral nature of the 3D preforms. 3D stress/strain and crack propagation analysis of composite Π-joint was performed using 3D MOSAIC code. 3D displacement, st ...

    SBIR Phase II 2006 Department of DefenseNavy
  5. Enhanced Rotorcraft Aerodynamic Modules to Support Flight Testing

    SBC: ADVANCED ROTORCRAFT TECHNOLOGY, INC.            Topic: N04257

    This SBIR is to develop advanced rotorcraft aerodynamic modules to significantly enhance and improve the analytical prediction of rotorcraft performance, stability, dynamic response, and loads to support vehicle design, manufacturing, operation, and flight testing. The research and development will address five critical application areas: rotor dynamic stall, modern rotor blade tip aerodynamics, u ...

    SBIR Phase II 2006 Department of DefenseNavy
  6. New Modeling and Simulation Technology for Night Vision Goggle Mission Rehearsal

    SBC: AECHELON TECHNOLOGY            Topic: N04156

    The Phase II investigation will result in the design of an economically priced part-task trainer for highly realistic introductory and refresher-level training of Night Vision Goggle phenomenology to aircrew. System will have the capability for courseware will be developed by instructors at the NITE Labs, and may be distributed to other NVG PTTs deployed world-wide.

    SBIR Phase II 2006 Department of DefenseNavy
  7. Lightweight Power Transformer for Shipboard Electrical Power Distribution Systems

    SBC: AEROVIRONMENT, INC.            Topic: OSD04EP5

    Shipboard power distribution requires both step-up and step-down transformation. Conventional 60Hz transformers, however, are both bulky and heavy. The proposed Phase II effort will develop a prototype 2.7MVA Electronic Transformer that combines high frequency switching power electronics and interphase transformer technology, with advanced digital signal processing for control. While a certain amo ...

    SBIR Phase II 2006 Department of DefenseNavy
  8. Sintered Conductive Adhesives for use in Active Radar System Thermal Management

    SBC: Aguila Technologies, Inc.            Topic: N04163

    Current Naval microwave power amplifiers operate at power densities around 200-500 W/cm2. Amplifiers under development may operate at 2-4 times this power density. Despite the development of active cooling technologies, the principal technology for removing heat from a chip remains thermal conduction. In most power devices, solders, such as AuSn, are used for die attach bonding. Solder is not adap ...

    SBIR Phase II 2006 Department of DefenseNavy
  9. Wireless Sensors with Advanced Detection and Prognostic Capabilities for Corrosion Health Management

    SBC: Analatom Inc            Topic: N04256

    The aim of this project is to build a wireless corrosion monitoring system that is specifically designed for the Joint Strike Fighter (JSF). Such systems are key elements in assuring the performance and reliability of the JSF while minimizing lifecycle costs associated with deteriorating nonmetallic and metallic material. The technology builds on the Analatom Linear Polarization Resistance (LPR) ...

    SBIR Phase II 2006 Department of DefenseNavy
  10. Shipping Container Remote Sensing

    SBC: AVAAK            Topic: SB041005

    Each year, more than sixteen million shipping containers arrive in the US via truck, rail, or container ships. Current inspection regimes rely on cumbersome and expensive procedures such as manual inspection and/or x-ray, gamma ray, and radiation detection technology to determine the risk posed by each container. Rarely can more than a small percentage of the total number of containers arriving a ...

    SBIR Phase II 2006 Department of DefenseNavy
US Flag An Official Website of the United States Government