Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Design and Realization of a Dual Function OCM/MPM for Imaging TEMPs

    SBC: Distant Focus Corporation            Topic: N/A

    Regenerative medicine is an emerging, interdisciplinary field that will result in new engineered medical products. The introduction of a high-resolution, non-destructive imaging technique that is capable of penetrating deeply into the highly-scattering scaffold medium has the means to accelerate the development and commercial utilization of these novel materials. Multi-photon microscopy (MPM) is b ...

    SBIR Phase II 2006 Department of CommerceNational Institute of Standards and Technology
  2. Improved Manufacturing Technologies for Polymer Matrix Composite Engine Components

    SBC: 2PHASE TECHNOLOGIES, INC.            Topic: AF06115

    This proposal addresses the development and use of lightweight, low thermal-capacity reformable tooling materials for high-temperature composite processing evaluation, parts prototyping, trial production and full-rate production of PMC engine components. The weight-saving promise of high-temperature polymer matrix composites (PMCs) for engine components is offset by the very high costs of parts m ...

    SBIR Phase I 2006 Department of DefenseAir Force
  3. Closed Loop Composite Recycling Process

    SBC: Adherent Technologies, Inc.            Topic: AF06081

    The recycling of composites on a large scale is an unsolved problem. Currently, the material is either ground up into near-worthless fillers, incinerated, or digested using environmentally questionable technology. Adherent Technologies, Inc. has developed a number of technologies to reclaim valuable carbon fiber and other raw materials from these composites in a potentially economically feasible ...

    SBIR Phase I 2006 Department of DefenseAir Force
  4. High-Resolution Wide-Dynamic-Range MEMS-Based Closed-Loop Adaptive Optics System

    SBC: AGILOPTICS            Topic: AF05003

    AgilOptics’ Phase I SBIR proposed the development of a moire¢ Wave-Front Sensor (MWFS) test-bed to evaluate the MWFS design developed and patented by the University of New Mexico (UNM) and to extend the design for use in a closed-loop Adaptive Optic (AO) system with a Micro-Electro-Mechanical System (MEMS) Deformable Mirror (DM) corrector. Our Phase I results have shown that the MWFS provides i ...

    SBIR Phase II 2006 Department of DefenseAir Force
  5. MEMS-Based Aero-optics Simulator System

    SBC: AGILOPTICS            Topic: AF06T030

    This effort joins the MEMS-based deformable mirror technology available from AgilOptics, a New Mexico small business, with the aero-optics technology of the University of Notre Dame to develop an Aero-optics Simulator. This simulator will develop a library of aero-optics patterns to simulate atmospheric distortions for test and evaluation of military or commercial beam control systems.

    STTR Phase I 2006 Department of DefenseAir Force
  6. Nano-Engineered Coating for Barrel Life Enhancement

    SBC: APPLIED THIN FILMS, INC.            Topic: AF06350

    Extending gun barrel life has been a long-standing goal for the US Air Force and other DoD agencies. Currently-used chrome plated barrels are susceptible to erosion and corrosion which affects the accuracy of fired bullets due to material loss along the inner surface. The primary cause of barrel degradation is the poor quality chrome coating and attack of steel inner surface by hot gases and comb ...

    SBIR Phase I 2006 Department of DefenseAir Force
  7. Formal-Verification-Based Tool for Deobfuscation of Tamper-Proofed Software

    SBC: Aries Design Automation, LLC            Topic: OSD06NC5

    The rapid increase in the use of the Internet in many aspects of our lives has led to an explosive growth in the spread of malware such as computer worms, viruses, and trojans. Security tools typically examine software for the presence of malware either by looking for specific byte signatures, or (more recently) by analyzing the candidate binary’s internal logic. However, it is surprisingly easy ...

    STTR Phase I 2006 Department of DefenseAir Force
  8. Tuneable Low Frequency Microwave Source

    SBC: ASR Corporation            Topic: AF05006

    The proposed effort is to develop a frequency and waveshape agile pulse forming system. The pulse forming system is based on a Blumlein topology and allows a wide range of waveforms to be generated from a fixed set of mechanical hardware.

    SBIR Phase II 2006 Department of DefenseAir Force
  9. Compact HPM Sources

    SBC: ASR Corporation            Topic: OSD05D07

    The MATRIX oscillator was developed as a tunable wideband HPM source for use by the AFRL in threat testing. The fundamental physics of hydrogen insulation used in the MATRIX oscillator as well as the overall topology limit the voltage-frequency-Q (VFQ) product of the current system. Through the application of dual-resonant topology and revised insulation, the output of the MATRIX oscillator conc ...

    SBIR Phase I 2006 Department of DefenseAir Force
  10. Development of commercially useable codes to simulate aluminized propellant combustion, and related issues

    SBC: BUCKMASTER RESEARCH            Topic: AF06T012

    We propose to examine the necessary ingredients for the development of marketable codes which will: model the morphology of heterogeneous propellants (a packing code); calculate the thermal and mechancial properties of such a morphology or pack; simulate the combustion of the pack; predict the statistics of aluminum agglomeration on the burning pack surface; simulate the flight of these agglomera ...

    STTR Phase I 2006 Department of DefenseAir Force
US Flag An Official Website of the United States Government