Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until September, 2020.

  1. Design and Realization of a Dual Function OCM/MPM for Imaging TEMPs

    SBC: Distant Focus Corporation            Topic: N/A

    Regenerative medicine is an emerging, interdisciplinary field that will result in new engineered medical products. The introduction of a high-resolution, non-destructive imaging technique that is capable of penetrating deeply into the highly-scattering scaffold medium has the means to accelerate the development and commercial utilization of these novel materials. Multi-photon microscopy (MPM) is b ...

    SBIR Phase II 2006 Department of CommerceNational Institute of Standards and Technology
  2. Improved Manufacturing Technologies for Polymer Matrix Composite Engine Components

    SBC: 2PHASE TECHNOLOGIES, INC.            Topic: AF06115

    This proposal addresses the development and use of lightweight, low thermal-capacity reformable tooling materials for high-temperature composite processing evaluation, parts prototyping, trial production and full-rate production of PMC engine components. The weight-saving promise of high-temperature polymer matrix composites (PMCs) for engine components is offset by the very high costs of parts m ...

    SBIR Phase I 2006 Department of DefenseAir Force
  3. Vinyl Ester Compatible High-Modulus Fiber System for Composite Laminates

    SBC: Adherent Technologies, Inc.            Topic: N04094

    An aqueous-based finish (sizing) was developed in Phase I to improve the carbon/vinyl ester interfacial bond. The finish is composed of a reactive coupling agent, a low viscosity vinyl ester resin, a free radical inhibitor, and a surfactant. The reactive finishes substantially improved the carbon/vinyl ester interface compared to unsized or FOE sized materials. Failure mode analysis shows that ...

    SBIR Phase II 2006 Department of DefenseNavy
  4. High Temperature Finishes/Sizings for Polyimide Matrix Composites

    SBC: Adherent Technologies, Inc.            Topic: N04251

    New high-temperature sizings are needed to improve the properties and durability of carbon/polyimide composites. Compatibility with weaving and braiding operations and improved wetting during prepregging or resin infusing polyimide resin is also needed. Achieving these characteristics will result in reducing life cycle costs for jet engine composites through better property translation, reduced ...

    SBIR Phase II 2006 Department of DefenseNavy
  5. Finishing Process to Improve Interfacial Bonding in SiC/BMI Composites

    SBC: Adherent Technologies, Inc.            Topic: N05025

    High-temperature (HT) polymer matrix composites (PMCs) are desired for many aerospace and military applications. Silicon carbide (SiC) fibers provide a potentially attractive reinforcement for HT PMCs for applications ranging from propulsion systems to structures for the orbiting space plane. The sizings routinely added to commercial SiC fibers are not compatible with the new HT matrix resins. ...

    SBIR Phase II 2006 Department of DefenseNavy
  6. Phosphorous-Containing Epoxy Resins for Room Temperature VARTM

    SBC: Adherent Technologies, Inc.            Topic: N06T017

    The Navy intends to start using a significant quantity of composite structures in surface ship construction in an effort to decrease costs as well as to reduce the visibility of the ships to radar. The large size of the target structures necessitates the use of low temperature, non-autoclave processing techniques such as Vacuum Assisted Resin Transfer Molding (VARTM). In the recent past, most m ...

    STTR Phase I 2006 Department of DefenseNavy
  7. Closed Loop Composite Recycling Process

    SBC: Adherent Technologies, Inc.            Topic: AF06081

    The recycling of composites on a large scale is an unsolved problem. Currently, the material is either ground up into near-worthless fillers, incinerated, or digested using environmentally questionable technology. Adherent Technologies, Inc. has developed a number of technologies to reclaim valuable carbon fiber and other raw materials from these composites in a potentially economically feasible ...

    SBIR Phase I 2006 Department of DefenseAir Force
  8. High-Resolution Wide-Dynamic-Range MEMS-Based Closed-Loop Adaptive Optics System

    SBC: AGILOPTICS            Topic: AF05003

    AgilOptics’ Phase I SBIR proposed the development of a moire¢ Wave-Front Sensor (MWFS) test-bed to evaluate the MWFS design developed and patented by the University of New Mexico (UNM) and to extend the design for use in a closed-loop Adaptive Optic (AO) system with a Micro-Electro-Mechanical System (MEMS) Deformable Mirror (DM) corrector. Our Phase I results have shown that the MWFS provides i ...

    SBIR Phase II 2006 Department of DefenseAir Force
  9. MEMS-Based Aero-optics Simulator System

    SBC: AGILOPTICS            Topic: AF06T030

    This effort joins the MEMS-based deformable mirror technology available from AgilOptics, a New Mexico small business, with the aero-optics technology of the University of Notre Dame to develop an Aero-optics Simulator. This simulator will develop a library of aero-optics patterns to simulate atmospheric distortions for test and evaluation of military or commercial beam control systems.

    STTR Phase I 2006 Department of DefenseAir Force
  10. Ambient Power Supply for On-Board Vehicle Health Monitoring MEMS Sensors

    SBC: AMBIENT MICRO            Topic: AF06170

    To support its use of MEMS sensors for vehicle health monitoring, the Air Force seeks to couple the harvesting of ambient energy sources with a micro energy storage device. Microbatteries have demonstrated their viability as a high density power source, but their short operating life limits their usefulness. To extend the operating life of microbatteries, ambient energy sources can be used to co ...

    SBIR Phase I 2006 Department of DefenseAir Force
US Flag An Official Website of the United States Government