List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. Ground-Based Water Vapor Profiling Lidar

    SBC: Bennett Aerospace, Inc.            Topic: 832

    The vertical water vapor profile into the atmosphere is measured around the world using balloon-borne radiosondes that take measurements twice a day when the balloons are launched.  The objective of this proposal is to establish the feasibility of measuring the amount of water vapor vertically, in the atmosphere as a function of altitude using a Light Detection and Ranging (lidar) operating i ...

    SBIR Phase I 2009 Department of Commerce
  2. Induction of Triploidy and Gynogenesis in Cobia (Rachycentron canadum)

    SBC: TROUTLODGE INC            Topic: 8110

    Cobia (Rachycentron canadum) exhibit differential growth rates between the sexes, with females growing faster than males.  Sex determination mechanisms have not been elucidated for this species, nor are there any literature reports regarding the induction of sterility through triploidy or attempts at generating uniparental inheritance. The research outlined in this proposal will establish pr ...

    SBIR Phase I 2009 Department of Commerce
  3. Development and Prototyping of a Digital Pulse Processor for Improved Coincidence Detection, Rejection, and Pulse Recovery, for High Count-Rate Silicon Drift Detectors

    SBC: 4pi Analysis, Inc.            Topic: N/A

    The recent emergence of the Silicon Drift detector (SDD), for use in energy dispersive x-ray spectrometry (EDS), has made possible x-ray event streams with count rates as high as 1-10 Mcps. A problem with existing digital signal processing, as applied to SDDs, is the significant presence of coincidence peaks above the x-ray background. These coincidence peaks occur with amplitudes comparable to lo ...

    SBIR Phase II 2009 Department of CommerceNational Institute of Standards and Technology
  4. Chemometric Support for Temperature-programmed Sensing System

    SBC: Eigenvector Research, Inc.            Topic: N/A

    The Temperature Programmed Sensing (TPS) system developed at NIST presents many opportunities and unique challenges. The data output from the system can be quite complex and there are many opportunities to optimize the system for specific sensing scenarios. We propose a program aimed at characterizing the system so that potential problems (such as system drift) can be solved early so that the full ...

    SBIR Phase I 2009 Department of CommerceNational Institute of Standards and Technology
  5. Environmentally Friendly Cold Plasma Coating Removal Techniques

    SBC: ATMOSPHERIC PLASMA SOLUTIONS            Topic: AF081041

    The DOD requires an environmentally friendly, rapid, and non-destructive method to selectively remove coatings from composite substrates.  Atmospheric Plasma Solutions Inc. (APS) has developed a cold atmospheric plasma process to accomplish this goal. Current processes for the removal of coatings from composite materials are slow, expensive, and potentially damaging to the environment. APS has de ...

    SBIR Phase II 2009 Department of DefenseAir Force
  6. Robust Wideband Aircraft Altitude Estimation for Over-the-Horizon HF Radar

    SBC: STRAD Corporation            Topic: AF083184

    Robust altitude estimation for over-the-horizon HF radar requires a combination of advanced signal processing and high fidelity ionospheric propagation modeling. Since aircraft height is manifested in closely-spaced direct and ground-bounce multipath reflections off the target, we propose two new high resolution signal processing methods for discriminating small time delay differences from a seque ...

    SBIR Phase I 2009 Department of DefenseAir Force
  7. Accelerated Development of High-Performance Mo-Si-B-X Alloys via an Approach of Integrating Thermodynamic Modeling with Experimental Study

    SBC: Computherm, LLC            Topic: AF07T003

    The proposed study aims at accelerated development of Mo-Si-B-X (X=Ti, Zr, Hf, Re, Mn) alloys with an optimized balance of properties, via an approach of integrating thermodynamic modeling with experimental study.   On the basis of the Mo-Si-B-X (X=Ti, Zr, Hf) database developed in Phase I, a thermodynamic database of the Mo-Si-B-O-X (X=Ti, Zr, Hf, Re, Mn) system will be developed using the Calp ...

    STTR Phase II 2009 Department of DefenseAir Force
  8. A Modeling Tool for Predicting the Durability of Environmental Barrier Coatings (EBC) for Ceramic Matrix Composites (CMC)

    SBC: Computherm, LLC            Topic: AF083070

    CompuTherm, LLC proposes a pilot project to develop a modeling tool that can be used to assess the durability of environmental barrier coatings (EBCs) for ceramic matrix composites (CMCs) under combustion environment. The modeling tool includes a thermodynamic database for the gas phase, a thermodynamic database for the silicate system (EBCs), and a computer software package that deals with thermo ...

    SBIR Phase I 2009 Department of DefenseAir Force
  9. Electrical power generation for sustained high speed flight

    SBC: Rivis, Inc.            Topic: AF08BT25

    Development of a compliant microfabricated heat exchanger to work with thermoelectric devices as a means of power generation for hypersonic vehicles is proposed. Polymer-based materials provide to provide compression on the thermoelectric module, to ensure optimal thermal contact, while allowing for compliance to allow for the change in materials expansion without exceeding the failure point of th ...

    STTR Phase I 2009 Department of DefenseAir Force
  10. Technologies for the Rapid Curing of Composite Parts

    SBC: FIREBIRD ADVANCED MATERIALS, INC.            Topic: AF083C068

    Certain polymer resins used in the manufacturing of carbon fiber reinforced polymer (CFRP) aerospace components have relatively long autoclave cure cycles on the order of 6 hours or more.  These long cure cycles cause bottlenecks and inefficiencies when producing composite parts with these thermoset resins. This project will investigate and develop a new manufacturing process for rapidly curing c ...

    SBIR Phase I 2009 Department of DefenseAir Force

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government