You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Development and Prototyping of a Digital Pulse Processor for Improved Coincidence Detection, Rejection, and Pulse Recovery, for High Count-Rate Silicon Drift Detectors

    SBC: 4pi Analysis, Inc.            Topic: N/A

    The recent emergence of the Silicon Drift detector (SDD), for use in energy dispersive x-ray spectrometry (EDS), has made possible x-ray event streams with count rates as high as 1-10 Mcps. A problem with existing digital signal processing, as applied to SDDs, is the significant presence of coincidence peaks above the x-ray background. These coincidence peaks occur with amplitudes comparable to lo ...

    SBIR Phase II 2009 Department of CommerceNational Institute of Standards and Technology
  2. Innovative Surface Treatments for Solar Cells

    SBC: APPLIED THIN FILMS, INC            Topic: AF073095

    Pursuits of highly efficient and reliable solar cells place high demands on the materials and processes used in their fabrication. For extraterrestrial cells, specific efficiency is of utmost importance, and thus the ability to reduce module weight without impacting efficiency is highly desirable. Flexible solar cells are a new direction in solar cell technology and robust substrates are required. ...

    SBIR Phase II 2009 Department of DefenseAir Force
  3. Environmentally Friendly Cold Plasma Coating Removal Techniques

    SBC: ATMOSPHERIC PLASMA SOLUTIONS, INC.            Topic: AF081041

    The DOD requires an environmentally friendly, rapid, and non-destructive method to selectively remove coatings from composite substrates.  Atmospheric Plasma Solutions Inc. (APS) has developed a cold atmospheric plasma process to accomplish this goal. Current processes for the removal of coatings from composite materials are slow, expensive, and potentially damaging to the environment. APS has de ...

    SBIR Phase II 2009 Department of DefenseAir Force
  4. Solid Propellant Shock to Detonation Modeling and Formulation

    SBC: BUCKMASTER RESEARCH            Topic: AF08T003

    Determining the hazard classification of new propellant formulations is important for transportation safety and storage concerns. To avoid costly grain redesign and additional testing, a model that adequately predicts the shock sensitivity, including the outcome of the Naval Ordnance Laboratory Large Scale Gap Test, of modern solid propellants is required. The goals of this proposal are to develop ...

    STTR Phase I 2009 Department of DefenseAir Force
  5. High Performance Low Integration Cost Magnetometer System

    SBC: LEE, JENNA            Topic: AF083218

    An innovative data collection and analysis approach is proposed to enable body mount magnetometers for space application. In order to achieve high accurate magnetic field measurement in space, the magnetometer has to be located in a âmagnetically cleanâ place, where the magnetic field from spacecraft is negligible. Usually, the magnetometers are placed on deployable booms, so that the field sens ...

    SBIR Phase I 2009 Department of DefenseAir Force
  6. Robust Wideband Aircraft Altitude Estimation for Over-the-Horizon HF Radar

    SBC: STRAD Corporation            Topic: AF083184

    Robust altitude estimation for over-the-horizon HF radar requires a combination of advanced signal processing and high fidelity ionospheric propagation modeling. Since aircraft height is manifested in closely-spaced direct and ground-bounce multipath reflections off the target, we propose two new high resolution signal processing methods for discriminating small time delay differences from a seque ...

    SBIR Phase I 2009 Department of DefenseAir Force
  7. Accelerated Development of High-Performance Mo-Si-B-X Alloys via an Approach of Integrating Thermodynamic Modeling with Experimental Study

    SBC: Computherm, LLC            Topic: AF07T003

    The proposed study aims at accelerated development of Mo-Si-B-X (X=Ti, Zr, Hf, Re, Mn) alloys with an optimized balance of properties, via an approach of integrating thermodynamic modeling with experimental study.   On the basis of the Mo-Si-B-X (X=Ti, Zr, Hf) database developed in Phase I, a thermodynamic database of the Mo-Si-B-O-X (X=Ti, Zr, Hf, Re, Mn) system will be developed using the Calp ...

    STTR Phase II 2009 Department of DefenseAir Force
  8. A Modeling Tool for Predicting the Durability of Environmental Barrier Coatings (EBC) for Ceramic Matrix Composites (CMC)

    SBC: Computherm, LLC            Topic: AF083070

    CompuTherm, LLC proposes a pilot project to develop a modeling tool that can be used to assess the durability of environmental barrier coatings (EBCs) for ceramic matrix composites (CMCs) under combustion environment. The modeling tool includes a thermodynamic database for the gas phase, a thermodynamic database for the silicate system (EBCs), and a computer software package that deals with thermo ...

    SBIR Phase I 2009 Department of DefenseAir Force
  9. Closed-Loop Process Control for Electron Beam Direct Manufacturing

    SBC: SCIAKY INC            Topic: AF083069

    The electron beam free form fabrication process (EBFFF) holds great promise for industry as a disruptive technology based on additive manufacturing of near net shape, high value engineered materials. The development efforts are structured to review and compare multiple process feedback systems for identifying molten pool characteristics and perform a series of open loop process parameter tests to ...

    SBIR Phase I 2009 Department of DefenseAir Force
  10. Electron-Beam Additive Manufacturing Process Control for Titanium Alloys

    SBC: SCIAKY INC            Topic: AF091C002

    Electron Beam Free Form Fabrication has the potential to produce large titanium structures directly from 3D models eliminating or reducing the long lead times associated with designing, procuring, and implementing conventional forging tooling as well as reducing the amount of machining cost by producing near net shapes. Our proposal outlines an approach to demonstrate the use of this technology su ...

    SBIR Phase I 2009 Department of DefenseAir Force
US Flag An Official Website of the United States Government