You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. An All-Fiber Mid-Infrared Frequency Combs

    SBC: ADVALUE PHOTONICS INC            Topic: AF08BT16

    A low-cost fiber-based octave-spanning frequency comb system operating in the mid-IR region is proposed, which is based on femtosecond-Tm-fiber-laser-pumped supercontinuum generation in a mid-IR-transmitting dispersion-engineered fiber. An all-fiber femtosecond mode-locked Tm-doped fiber laser at 2 micron will be used as a seed source for mid-IR supercontinuum generation. A femtosecond soliton fib ...

    STTR Phase I 2009 Department of DefenseAir Force
  2. Low Cost Intelligence, Surveillance and Reconnaissance, Unmanned Aerial Vehicle (UAV)

    SBC: Sensintel Inc.            Topic: AF083006

    An approach to make a long endurance UAV with an 18 hour endurance and large payload will be developed based on an existing, fielded capability present operationally deployed.  The system will be built from COTS equipment minimizing cost and allowing for rapid maintenance and upgrading of the system as technology develops.  The system will be fully autonomous through launch, mission flight and r ...

    SBIR Phase I 2009 Department of DefenseAir Force
  3. Handheld Real Time (RT) Climatic/Environmental Sensor

    SBC: VIRTUAL TECHNOLOGY LLC            Topic: AF073110

    This proposal will provide immediate decision support data, enabling appropriate and cost effective responses (shut down vs. continue) for training exercises/facilities. Specifically, the DoD requires the ability to “train as we fight and fight as we train”, however training is severely limited by visible emissions compliance in the current regulatory environment. Regulated facilities will hav ...

    SBIR Phase II 2009 Department of DefenseAir Force
  4. Environmentally Friendly Cold Plasma Coating Removal Techniques

    SBC: ATMOSPHERIC PLASMA SOLUTIONS, INC.            Topic: AF081041

    The DOD requires an environmentally friendly, rapid, and non-destructive method to selectively remove coatings from composite substrates.  Atmospheric Plasma Solutions Inc. (APS) has developed a cold atmospheric plasma process to accomplish this goal. Current processes for the removal of coatings from composite materials are slow, expensive, and potentially damaging to the environment. APS has de ...

    SBIR Phase II 2009 Department of DefenseAir Force
  5. High Performance Low Integration Cost Magnetometer System

    SBC: LEE, JENNA            Topic: AF083218

    An innovative data collection and analysis approach is proposed to enable body mount magnetometers for space application. In order to achieve high accurate magnetic field measurement in space, the magnetometer has to be located in a âmagnetically cleanâ place, where the magnetic field from spacecraft is negligible. Usually, the magnetometers are placed on deployable booms, so that the field sens ...

    SBIR Phase I 2009 Department of DefenseAir Force
  6. Robust Wideband Aircraft Altitude Estimation for Over-the-Horizon HF Radar

    SBC: STRAD Corporation            Topic: AF083184

    Robust altitude estimation for over-the-horizon HF radar requires a combination of advanced signal processing and high fidelity ionospheric propagation modeling. Since aircraft height is manifested in closely-spaced direct and ground-bounce multipath reflections off the target, we propose two new high resolution signal processing methods for discriminating small time delay differences from a seque ...

    SBIR Phase I 2009 Department of DefenseAir Force
  7. Accelerated Development of High-Performance Mo-Si-B-X Alloys via an Approach of Integrating Thermodynamic Modeling with Experimental Study

    SBC: Computherm, LLC            Topic: AF07T003

    The proposed study aims at accelerated development of Mo-Si-B-X (X=Ti, Zr, Hf, Re, Mn) alloys with an optimized balance of properties, via an approach of integrating thermodynamic modeling with experimental study.   On the basis of the Mo-Si-B-X (X=Ti, Zr, Hf) database developed in Phase I, a thermodynamic database of the Mo-Si-B-O-X (X=Ti, Zr, Hf, Re, Mn) system will be developed using the Calp ...

    STTR Phase II 2009 Department of DefenseAir Force
  8. A Modeling Tool for Predicting the Durability of Environmental Barrier Coatings (EBC) for Ceramic Matrix Composites (CMC)

    SBC: Computherm, LLC            Topic: AF083070

    CompuTherm, LLC proposes a pilot project to develop a modeling tool that can be used to assess the durability of environmental barrier coatings (EBCs) for ceramic matrix composites (CMCs) under combustion environment. The modeling tool includes a thermodynamic database for the gas phase, a thermodynamic database for the silicate system (EBCs), and a computer software package that deals with thermo ...

    SBIR Phase I 2009 Department of DefenseAir Force
  9. Electrical power generation for sustained high speed flight

    SBC: RIVIS, INC.            Topic: AF08BT25

    Development of a compliant microfabricated heat exchanger to work with thermoelectric devices as a means of power generation for hypersonic vehicles is proposed. Polymer-based materials provide to provide compression on the thermoelectric module, to ensure optimal thermal contact, while allowing for compliance to allow for the change in materials expansion without exceeding the failure point of th ...

    STTR Phase I 2009 Department of DefenseAir Force
  10. Technologies for the Rapid Curing of Composite Parts

    SBC: FIREBIRD ADVANCED MATERIALS, INC.            Topic: AF083C068

    Certain polymer resins used in the manufacturing of carbon fiber reinforced polymer (CFRP) aerospace components have relatively long autoclave cure cycles on the order of 6 hours or more.  These long cure cycles cause bottlenecks and inefficiencies when producing composite parts with these thermoset resins. This project will investigate and develop a new manufacturing process for rapidly curing c ...

    SBIR Phase I 2009 Department of DefenseAir Force
US Flag An Official Website of the United States Government