List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. STOICHIOMETRIC DIESEL ENGINE

    SBC: ADIABATICS INCORPORATED            Topic: N/A

    A FEASIBILITY STUDY ON THE DEVELOPMENT OF A STOICHIOMETRIC DIESEL ENGINE IS PROPOSED USING THE THERMAL IGNITION COMBUSTION CHAMBER. THE ADIABATIC DIESEL ENGINE WITHOUT WATER OR AIR COOLING ALLOWS THE THERMAL IGNITION CHAMBER TO STORE HEAT DURING COMBUSTION AND RELEASE THE ENERGY FOR IGNITION IN THE FOLLOWING CYCLE. INJECTION OF FUEL ON TO 1800-2000 DEG. F WALL TEMPERATURE WILL PREPARE THE FUEL FOR ...

    SBIR Phase II 1989 Department of DefenseArmy
  2. HYPERSONIC RAMJET LEADING EDGE MATERIALS DEVELOPMENT

    SBC: Technology Holding, LLC            Topic: N/A

    CERAMATEC HAS CONDUCTED EXPLORATORY RESEARCH AND DEVELOPMENT ON MONOLITHIC AND COMPOSITE MATERIALS IN THE ZRB2 AND TIB2 SYSTEMS AND HAS OBTAINED VERY ENCOURAGING RESULTS WITH SEVERAL PROPRIETARY COMPOSITIONS/CONSTRUCTIONS. THE AVERAGE STRENGTH OF A BASELINE TIB2 COMPOSITION WAS MEASURED AT 877 MPA (127.3 KSI). COMPOSITE STRUCTURESWITH DISCONTINUOUS REINFORCEMENT HAD STRENGTHS IN THE RANGE 400-600 ...

    SBIR Phase II 1989 Department of DefenseNavy
  3. INJECTION MOLDING OF CERAMIC MATRIX COMPOSITES

    SBC: Technology Holding, LLC            Topic: N/A

    THE OVERALL OBJECTIVE OF THIS PROJECT IS TO DEMONSTRATE THE SUCCESSFUL FABRICATION AND DENSIFICATION OF CERAMIC MATRIX COMPOSITES FORMED BY INJECTION MOLDING. TO ACCOMPLISH THIS OBJECTIVE, A DESIGNED TEST MATRIX WILL BE DEVELOPED THAT WILL SYSTEMATICALLY INVESTIGATE THE KEY INJECTION MOLDING AND DEBINDING PARAMETERS SUCH AS BINDER COMPOSITION, SOLIDS RATIO, MOLDING CONDITIONS, DEBINDING CONDITIONS ...

    SBIR Phase II 1989 Department of DefenseNavy
  4. ELECTRICAL FAULT CURRENT LIMITER

    SBC: Powertronic System, Inc.            Topic: N/A

    THE OBJECTIVE OF PHAE I IS TO DETERMINE BY AN ANALYTICAL STUDY THE OPTIMUM DESIGN APPROACH, OR APPROACHES, FOR SOLID-STATE ELECTRICAL FAULT CURRENT LIMITERS FOR THE CURRENT RANGE OF 15 TO 5000 AMPERES. THE ANALYTICAL TRADEOFF STUDY WILL INCLUDE THE FOLLOWING TASKS: 1) DEFINITION OF CURRENT LIMITER REQUIREMENTS, 2) DEFINITION OF TRADEOFF ANALYSIS CRITERIA, 3) DEFINITION OF CANDIDATE CURRENT LIMITER ...

    SBIR Phase II 1989 Department of DefenseNavy
  5. LIPOSOME SIALIDATION

    SBC: Siagenic Inc.            Topic: N/A

    THIS PROPOSAL IS TO DEMONSTRATE FEASIBILITY OF INSERTION OF SIALIC ACID MOLECULES INTO MEMBRANES OF LIPOSOMES CARRYING HEMOGLOBIN. THE LIPOSOMES MAY BE PROVIDED BY NAVY CONTRACTORS OR PREPARED BY OFFEROR ACCORDING TO CONTRACTORS' SPECIFICATIONS FOR FOMULATION. THE ADDED SIALIC ACID WILL PROTECT THE LIPOSOMES FROM CLEARANCE BY THE RETICULOENDOTHELIAL SYSTEM AND THEREBY INCREASE THE RESIDENCY TIME O ...

    SBIR Phase II 1989 Department of DefenseNavy
  6. MANUFACTURE OF HIGH T(C) SUPERCONDUCTING COMPOSITE WIRES

    SBC: Technical research Associates, Inc.            Topic: N/A

    IN ORDER TO USE THE NEW CERAMIC SUPERCONDUCTOR MATERIALS IN MANY APPLICATIONS, THE NORMALLY BRITTLE MATERIALS MUST BE FORMED INTO WIRES. THIS PROPOSAL SUGGESTS A WET CHEMISTRY TECHNIQUE FOR FORMING THE SUPERCONDUCTOR COMPOUND INTO A WIRE, WHICH WILL THEN BE COATED WITH A METAL JACKET TO PROTECT THE WIRE FORM PHYSICAL ABUSE AND ENVIRONMENTAL DEGRADATION. BECAUSE THE COATING PROCESS WILL BE ESSENTIA ...

    SBIR Phase II 1989 Department of DefenseNavy
  7. NEW TECHNOLOGY IN THE USE OF HIGH TEMPERATURE COATINGS AS A REFERENCE FOR ULTRA HIGH TEMPERATURE STRAIN MEASURMENTS

    SBC: Terra Tek Inc.            Topic: N/A

    CURRENT METHODS USED TO MEASURE STRAIN AT HIGH TEMPERATURES DEPEND ON UNDESIRABLE ATTACHMENTS, EXTENSIONS, OR INDENTATIONS OF THE TEST SAMPLES. THIS STUDY WILL INVESTIGATE THE USE OF NEW TECHNOLOGY TO APPLY HIGH TEMPERATURE COATING MARKS TO TEST SAMPLES. THESE APPLIED MARKS WILL ACT AS A REFERENCE OR GAUGE FOR OPTICAL STRAIN MEASUREMENT. MATERIALS INCLUDING REFRACTORY METALS AND CERAMICS WILL BE A ...

    SBIR Phase II 1989 Department of DefenseAir Force
  8. ONE-MILLION POUND COMPRESSION REACTION LOADER AND COMPUTER CONTROL SYSTEM DESIGN

    SBC: Terra Tek Inc.            Topic: N/A

    A ONE-MILLION POUND COMPRESSION REACTION LOADER IS REQUIRED TO OPERATE IN CONJUNCTION WITH THE WATERWAYS EXPERIMENT STATION 6-KBAR TRIAXIAL TEST DEVICE. TERRA TEK HAS DESIGNED AND CONSTRUCTED SIMILAR TEST SYSTEMS FOR IN-HOUSE TESTING. TERRA TEK HAS ALSO DEVELOPED UNIQUE COMPUTER CONTROL CODES SPECIFICALLY FOR ROCK MECHANICS APPLICATIONS. THE PROPOSED PHASE I EFFORT IS TO DESIGN A COMPRESSION REACT ...

    SBIR Phase II 1989 Department of DefenseArmy
  9. FATIGUE LIFE PREDICTION BASED ON THREE-DIMENSIONAL STRESS ANALYSIS

    SBC: Terra Tek Inc.            Topic: N/A

    THE NAVY IS DEVELOPING METHODS TO DETERMINE THE SIZE AND TYPE OF DEFECTS IN HELICOPTER GEARBOXES. WITH THIS KNOWLEDGE A BETTER UNDERSTANDING OF THE FATIGUE-CRACK PROPAGATION CHARACTERISTICS OF THE GEARS AND BEARINGS WILL BE POSSIBLE AND ENHANCE THE ACCURACY IN PREDICTING THE FATIGUE LIFE. THE PURPOSE OF THIS PROPOSAL IS TO UNDERTAKE THIS STEP BY INVESTIGATING THE THREE-DIMENSIONAL STRESS DISTRIBUT ...

    SBIR Phase II 1989 Department of DefenseNavy

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government