You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. Reconfiguration of Component Level Control Network Automation Systems

    SBC: Adept Systems, Inc.            Topic: N/A

    "This project will develop and implement in embedded hardware the capability needed to configure pre hit, a component level automation infrastructure.This approach optimizes survivability using models of damage or casualty scenarios. This capability willbe demonstrated in a laboratory hardware in the loop simulation. This project leverages the results of several other ongoing research efforts al ...

    STTR Phase II 2002 Department of DefenseNavy
  2. HYPERSONIC RAMJET LEADING EDGE MATERIALS DEVELOPMENT

    SBC: Technology Holding, LLC            Topic: N/A

    CERAMATEC HAS CONDUCTED EXPLORATORY RESEARCH AND DEVELOPMENT ON MONOLITHIC AND COMPOSITE MATERIALS IN THE ZRB2 AND TIB2 SYSTEMS AND HAS OBTAINED VERY ENCOURAGING RESULTS WITH SEVERAL PROPRIETARY COMPOSITIONS/CONSTRUCTIONS. THE AVERAGE STRENGTH OF A BASELINE TIB2 COMPOSITION WAS MEASURED AT 877 MPA (127.3 KSI). COMPOSITE STRUCTURESWITH DISCONTINUOUS REINFORCEMENT HAD STRENGTHS IN THE RANGE 400-600 ...

    SBIR Phase II 1989 Department of DefenseNavy
  3. INJECTION MOLDING OF CERAMIC MATRIX COMPOSITES

    SBC: Technology Holding, LLC            Topic: N/A

    THE OVERALL OBJECTIVE OF THIS PROJECT IS TO DEMONSTRATE THE SUCCESSFUL FABRICATION AND DENSIFICATION OF CERAMIC MATRIX COMPOSITES FORMED BY INJECTION MOLDING. TO ACCOMPLISH THIS OBJECTIVE, A DESIGNED TEST MATRIX WILL BE DEVELOPED THAT WILL SYSTEMATICALLY INVESTIGATE THE KEY INJECTION MOLDING AND DEBINDING PARAMETERS SUCH AS BINDER COMPOSITION, SOLIDS RATIO, MOLDING CONDITIONS, DEBINDING CONDITIONS ...

    SBIR Phase II 1989 Department of DefenseNavy
  4. Simulating Detection System Output Data for the Development of Decision Support Systems

    SBC: COGNITECH CORPORATION            Topic: N/A

    "Accurately simulating sensor data is necessary to develop meaningful and effective decision support systems. This process requires the inclusion of all phenomena that significantly influence the data after propagation through the detection chain. Phase Ideveloped a prototype framework, methodology and simulation environment for propagating noise and uncertainty through components of a general d ...

    SBIR Phase II 2002 Department of DefenseNavy
  5. Stealth UAV Propulsion and Control Technology

    SBC: COMPOSITEX, INC.            Topic: N/A

    "Compositex proposes to continue the development of a revolutionary, high-performance stealth UAV platform. The goal is to develop a small fixed-wing UAV platform that is quiet, undetectable by radar, and can sustain flight at very low airspeeds. Theproposed aircraft system utilizes an upper surface blowing device to propel and control the craft, and also enabling it to attain maximum lift coeff ...

    SBIR Phase II 2002 Department of DefenseAir Force
  6. Freeze-Dried Reagents for real-time PCR

    SBC: IDAHO TECHNOLOGY            Topic: N/A

    "The Idaho Technology RAPID is currently the only fieldable DNA-based system available for monitoring threat agents such as Bacillus anthracis and Yersinia pestis. It has been deployed throughout the Air Force and other branches of the military with a highlevel of operational success. Typical PCR methods used with the RAPID are tied to complex wet chemistry more suitable for the laboratory than ...

    SBIR Phase II 2002 Department of DefenseOffice for Chemical and Biological Defense
  7. N/A

    SBC: Materials and Systems Research, Inc.            Topic: N/A

    N/A

    SBIR Phase II 1999 Department of DefenseAir Force
  8. N/A

    SBC: Patterned Fiber Composites, Inc.            Topic: N/A

    N/A

    SBIR Phase II 1999 Department of DefenseAir Force
  9. N/A

    SBC: PROCESS INSTRUMENTS, INC.            Topic: N/A

    N/A

    SBIR Phase II 1999 Department of DefenseMissile Defense Agency
  10. MANUFACTURE OF HIGH T(C) SUPERCONDUCTING COMPOSITE WIRES

    SBC: Technical research Associates, Inc.            Topic: N/A

    IN ORDER TO USE THE NEW CERAMIC SUPERCONDUCTOR MATERIALS IN MANY APPLICATIONS, THE NORMALLY BRITTLE MATERIALS MUST BE FORMED INTO WIRES. THIS PROPOSAL SUGGESTS A WET CHEMISTRY TECHNIQUE FOR FORMING THE SUPERCONDUCTOR COMPOUND INTO A WIRE, WHICH WILL THEN BE COATED WITH A METAL JACKET TO PROTECT THE WIRE FORM PHYSICAL ABUSE AND ENVIRONMENTAL DEGRADATION. BECAUSE THE COATING PROCESS WILL BE ESSENTIA ...

    SBIR Phase II 1989 Department of DefenseNavy
US Flag An Official Website of the United States Government