You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Prediction of the Full-Scale Cook-off Response Based on Small-Scale Testing

    SBC: BLAZETECH CORPORATION            Topic: N10AT011

    Reducing the violence of Slow Cook-Off (SCO) and Fast Cook-Off (FCO) to acceptable levels is of great interest to the Insensitive Munitions development. For example, the MIL-STD-2105C SCO test for Insensitive Munitions (IM) compliance requires a slow heating rate (3.3°C/hr) until reaction occurs whereby the ensuing reaction is characterized by degree of violence. A Type V (burn) reaction or bette ...

    STTR Phase II 2018 Department of DefenseNavy
  2. Shallow Water and Surf Zone Minehunting (MAD Swarm)

    SBC: Physical Sciences Inc.            Topic: AF08T008

    The Shallow Water and Surf Zone Minehunting program (MAD SWARM) is described that spans the development and demonstration of swarming micro-air vehicles (MAV’s) equipped with Magnetic Anomaly Detectors (MAD’s) to autonomously detect and locate mine targets in shallow water and the surf zone. The MAD Swarm system incorporates low cost micro-air vehicle (MAV) technology, swarming sensor search/c ...

    STTR Phase II 2018 Department of DefenseNavy
  3. Evidence-Based, User-Centered Design Process for Improvement of the Utility of the Surface Electronic Warfare Display Suit

    SBC: PACIFIC SCIENCE & ENGINEERING GROUP, INC.            Topic: N11AT031

    In Naval, surface electronic warfare (EW), visual displays form critical bridges between warfighters and the complex operational radio-frequency (RF) spectrum they must monitor and interpret. Surface electronic warfare operators and supervisors must monitor and interact with multiple, stove-piped display systems in order to perform their work. Further, the visual displays they employ are not desig ...

    STTR Phase II 2018 Department of DefenseNavy
  4. Solid-State Fundamental Mode Green Laser for Ocean Mine Detection

    SBC: Arete Associates            Topic: N13AT023

    Areté proposes the development of Q-switched semiconductor lasers that can be scaled to produce high output peak powers within the blue/green wavelength band. The proposed system will utilize nanostructure quantum wavefunction engineering for gain material designs having extended excited state lifetimes and suppressed non-radiative processes to enable energy storage for high-peak-power optical pu ...

    STTR Phase II 2018 Department of DefenseNavy
  5. High Hesitivity Magnetic Materials for Magnetic Toroid and Flat Dipole Antennas

    SBC: Winchester Technologies, LLC            Topic: N16AT001

    Magnetic materials with high hesitivity values are needed to achieve low-profile conformal broadband magnetodielectric antennas with significantly enhanced efficiency in HF-UHF. The higher the hesitivity, the higher the attainable efficiency in these magnetodielectric antennas. State of the art hesitivity as high as 6×10^6 O/m has been reported in CoZrNb alloy films. Further hesitivity improvemen ...

    STTR Phase II 2018 Department of DefenseNavy
  6. System to Evaluate and Assess Holistic Aircrew Workload (SEAHAWK)

    SBC: Charles River Analytics, Inc.            Topic: N16AT002

    The Navy is continually developing new technologies to improve warfighting effectiveness. These technologies risk overloading Aircrews cognitive capacities, degrading performance. To mitigate that risk, the Navy needs a system to assess Aircrews physical and cognitive workloads unobtrusively and objectively. To meet these requirements, Charles River Analytics conducted a Phase I effort to design a ...

    STTR Phase II 2018 Department of DefenseNavy
  7. TOME: Tools for Objective Measurement and Evaluation

    SBC: Aptima, Inc.            Topic: N16AT002

    The introduction of new systems and technologies is critical for maintaining superiority, yet this brings with it uncertainty regarding the impact on users, teams, and organizations. Rigorous test and evaluation (T&E) practices are essential prior to acquiring and instituting new technologies, particularly to objectively assess the workload imposed on end users. Aptima, Inc. and its partners – S ...

    STTR Phase II 2018 Department of DefenseNavy
  8. Innovative Multi-scale/Multi-physics based Tool for Predicting Fatigue Crack Initiation and Propagation in Aircraft Structural Components using Phase

    SBC: Coreform LLC            Topic: N16AT003

    The purpose of this Phase II project is to develop computational modeling methods that are able to describe the propagation and interaction of fatigue cracks using the phase-field methodology within the numerical framework of isogeometric analysis (IGA). The resulting computational platform, while focused on fracture and fatigue, will be general, in that any phase-field method can be easily incorp ...

    STTR Phase II 2018 Department of DefenseNavy
  9. Perovskite Solar Cells

    SBC: Radiation Monitoring Devices, Inc.            Topic: N16AT006

    To provide power for unmanned aircraft systems (UAS), we propose developing solar cells made using perovskite halide solar absorbers, such as those based upon methylammonium lead iodide (CH3NH3PbI3). Our phase I efforts produced flexible solar cells that exhibited power conversion efficiencies (PCE) of 8.1%, a landmark achievement. The proposed research details how to achieve 20% power conversion ...

    STTR Phase II 2018 Department of DefenseNavy
  10. Additive Manufacturing for Microwave Vacuum Electron Device Cost Reduction

    SBC: Radiabeam Technologies, LLC            Topic: N16AT010

    The Department of the Navy has a need for the development of an additive manufacturing (AM) process for key vacuum electronic device components to meet on-demand, flexible, and affordable manufacturing requirements. The goal of this Phase II effort is to develop and validate Electron Beam Melting (EBM) additive manufacturing (AM) technology for the production of vacuum electronic devices meeting t ...

    STTR Phase II 2018 Department of DefenseNavy
US Flag An Official Website of the United States Government