Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. High-Speed Dynamic 3D Surface Mapping System

    SBC: Conrad Technologies, Inc.            Topic: N/A

    Conrad Technologies, Inc. (CTI) proposes a non-contact, dynamic 3D position sensor based on optical triangulation using multiple radiating LED targets to measure intrusion of an automobile structure into the occupant compartment during full-scale crash tests. CTI has significant experience developing non-contact measurement instruments. CTI has developed a Motion Imaging and Tracking Acquisition ...

    SBIR Phase I 2002 Department of Transportation
  2. Crack Arrest and Structural Repair of High Strength Steel Piping by In-Situ Sleeving of Nanostructural Materials

    SBC: Integran Technologies U.S.A. Inc.            Topic: 07PH1

    This proposal describes the application of a mature nanotechnology-based crack arrest / structural repair technology as a novel crack arrestor tool for high-strength pipelines. The crack arrestor would comprise a thin layer or sleeve of electrodeposited nanocrystalline material applied to the outside of the pipe either in the coating mill during fabrication or in-field during or following constru ...

    SBIR Phase I 2008 Department of Transportation
  3. Structural Repair of Steel Piping by In-Situ Sleeving of Nanostructured Materials

    SBC: Integran Technologies U.S.A. Inc.            Topic: N/A

    This proposal describes the application of a mature nanotechnology-based crack arrest/structural repair technology as a novel in-field pipeline repair tool. The repair would be comprised of a thin layer or sleeve of electrodeposited nancrystalline material applied to the damaged region of the pipe in order to utilize the "crack filling" characteristic of the process. The concept proposed has alr ...

    SBIR Phase I 2008 Department of Transportation
  4. Compact Laser Shearography System for Crack Detection

    SBC: Laser Technology Inc.            Topic: 05FH1

    Laser Technology Inc. (LTI) proposes a Phase II SBIR research project to further develop a Compact Shearography System, Analysis Method and Software for micro-crack detection in concrete. There is an urgent need to detect and characterize fine cracks in concrete that form because of various damage mechanisms including alkali-silicate reaction, delayed ettringite formation or frost damage. Fine s ...

    SBIR Phase II 2008 Department of Transportation
  5. Evaluation of Composite Joints in General Aviation Structures

    SBC: Materials Sciences LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase II 2002 Department of Transportation
  6. Evaluation of Composite Joints in General Aviation Structures

    SBC: Materials Sciences LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase I 2002 Department of Transportation
  7. Microscopic Traffic Flow Simulation Models- An Open Source Approach

    SBC: New Global Systems for Intelligent Transportation Management            Topic: 081FH5

    In the Open-source microscopic traffic simulation models project, a component based software framework is proposed to re-engineer CORISM data struture and CORISM interface. Under the architecture combing the innovative framework and the legacy CORISM, prototype of the open source traffic flow simulation models will be developed and demonstrated in the Phase I. In addition, areas identified by th ...

    SBIR Phase I 2008 Department of Transportation
  8. HYBRID POLYMERIC GLAZING MATERIALS

    SBC: Rolltrusion Inc.            Topic: N/A

    A NEW PROCESS IS PROPOSED FOR THE APPLICATION OF POLYMERIC MATERIALS FOR AUTOMOTIVE WINDOWS. SEMI-CRYSTALLINE POLYMERIC MATERIALS CAN BE RENDERED CLEAR THROUGH 3-D ORIENTATION VIA SOLID STATE PROCESSING. APPLYING THIS TECHNOLOGY TO A HYBRID POLYMER STRUCTURE CAN RESULT IN CHEMICALLY RESISTANT, MECHANICALLY STRONG, OPTICALLY CLEAR AND ECONOMICALLY VIABLE PLASTIC WINDOWS FOR GROUND TRANSPORTATION.

    SBIR Phase I 1993 Department of Transportation
  9. Low Cost Transverse Rail Defect Detector

    SBC: Mide Technology Corporation            Topic: 02FR1

    Development of the basic EMAT based transverse rail defect detector has progressed toward finished form, as envisioned in the original solicitation. This modification is intended to produce a demonstratable version of a 2-rail detection system with automated signal interpertation. The objectives of this work are to: a. Further develop the system into a functioning 2-rail detection system, as ori ...

    SBIR Phase II 2008 Department of Transportation
US Flag An Official Website of the United States Government