You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Fast Response Fabric Test Setup and Dynamic Fabric Model for BURNSIM

    SBC: Advanced Cooling Technologies, Inc.            Topic: AF071025

    Advanced Cooling Technologies, Inc. (ACT) will develop a Fast Thermal Response Fabric Test Setup for various thermal hazard scenarios involving convection (hot gas impingement by the jet engine exhaust), radiation (fire) and combination of convection and radiation (post-crash fire of aircraft, fire flash or bomb blast). The fabric test setup will (i) measure the thermal response of various clothin ...

    SBIR Phase II 2008 Department of DefenseAir Force
  2. Develop High-Temperature, Low-Humidity Aromatic Hydrocarbon-based H2/O2 Membranes for Proton Exchange Membrane (PEM) Fuel Cells

    SBC: AKRON POLYMER SYSTEMS, INC.            Topic: AF071130

    In order to achieve high performance at acceptable cost, PEM fuel cells are required to work at elevated temperature and low relative humidity (near 0 RH) for extended periods of time. However, to date, no commercial PEMs or publicly reported PEMs can meet these requirements. The objectives of this work are: (1) to develop PEMs that have high proton conductivities (50-100 mS/cm) and low area-spec ...

    SBIR Phase II 2008 Department of DefenseAir Force
  3. Environmentally Friendly Cleaning for Titanium Welds and Brazing

    SBC: APPLICATIONS TECHNOLOGIES CO.LLC            Topic: AF06326

    The first critical step in welding or brazing is cleaning to remove surface contamination. The Air Force has a need for an environmentally cleaning method that has no waste stream, minimal requirements of personal safety protection, and does not impact component integrity. The Arc Scrubber is an emerging non-chemical cleaning technology that utilizes and electrical arc to remove surface contamin ...

    SBIR Phase II 2008 Department of DefenseAir Force
  4. Unresolved Resident Space Object Characterization Using Time-Frequency Analysis

    SBC: Applied Optimization, Inc            Topic: AF071283

    Applied Optimization, Inc. [AO] proposes to demonstrate full feature characterization of unresolved RSOs by performing spectral unmixing and time-frequency analysis of its time and spectrally resolved signature in the visible or infrared spectrum. The characterization will be performed step-by-step by following a taxonomy of feature extraction. Materials identification will be performed via spectr ...

    SBIR Phase II 2008 Department of DefenseAir Force
  5. Advanced NDE for SiC Optics Using Micromachined High Frequency Phased Array Ultrasound

    SBC: TRS CERAMICS, INC.            Topic: AF071142

    TRS is pleased to propose an in-situ NDE imaging tool for SiC mirror surface damage (SD), sub-surface damage (SSD) and trapped internal stress detection using piezo-composite based micromachined ultrasound transducer (PCMUT) phased array technology. PCMUT technology has been developed at TRS to fabricate high frequency ultrasound transducers with broad bandwidth and high sensitivity. Phased array ...

    SBIR Phase II 2008 Department of DefenseAir Force
  6. Virtual Environment Composable Training for Operational Readiness – Total Instructional Package (VECTOR-TIP)

    SBC: CHI Systems, Inc.            Topic: OSD06CR8

    Cultural skills are increasingly important for military actions recently undertaken by the U.S., where close continuous contact with the indigenous population is necessary. All ground forces being deployed in culturally distinct and sensitive areas need to have at least some basics skills, knowledge, and awareness of cultural norms and prohibitions. Passive learning via lectures, tutorials, vide ...

    SBIR Phase II 2008 Department of DefenseAir Force
  7. Improving Weapons Bay Acoustical Environments

    SBC: COMBUSTION RESEARCH AND FLOW TECHNOLOGY INC            Topic: AF071256

    The F-22A main weapons bay experiences severe acoustic loading when exposed to the freestream. The severity and attenuation of this loading is exacerbated by the flight envelope of the F-22A aircraft, as well as the requirement to carry and release “smart” weapons throughout this envelope. This extremely harsh environment can also impact components that are mounted within the bay itself, inclu ...

    SBIR Phase II 2008 Department of DefenseAir Force
  8. Turbopump Cavitation Tools

    SBC: COMBUSTION RESEARCH AND FLOW TECHNOLOGY INC            Topic: AF071204

    Next generation liquid rocket systems envision novel designs for turbopumps that can operate at high suction speeds (i.e. low inlet pressures), and can be throttled over a wide range of low, off-design flow conditions. This is an extremely demanding flow regime where performance loss and damage from cavitation instabilities can be catastrophic since they can generate large amplitude pressure fluc ...

    SBIR Phase II 2008 Department of DefenseAir Force
  9. General Hypersonic Propulsion

    SBC: COMBUSTION RESEARCH AND FLOW TECHNOLOGY INC            Topic: AF071185

    Upgrades to a RANS Scalar fluctuation model (SFM) used to predict variations in turbulent Prandtl and Schmidt numbers in a scramjet combustor environment are proposed. Such upgrades will permit obtaining more accurate solutions leading to improved combustor designs. Experiments to be performed in Virginia Tech (and AFRL) facilities using existing models will be performed focused on SFM validation ...

    SBIR Phase II 2008 Department of DefenseAir Force
  10. Improved inspection of Bonded Repairs

    SBC: Fbs, Inc.            Topic: AF071325

    Bonded joints are used extensively for both civilian and military aircraft applications, especially for corrosion damage mitigation via patch bonding. Assessing the quality of these bonds is typically performed using NDE techniques such as bulk wave ultrasonics or thermography. These methods cannot reliably differentiate between a good bond and a so-called "kissing" bond. A kissing bond has no mec ...

    SBIR Phase II 2008 Department of DefenseAir Force
US Flag An Official Website of the United States Government