Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Crystal Properties and Transducer Modeling for High Power Composite & Tonpilz Projector Design

    SBC: TRS CERAMICS, INC.            Topic: N08061

    TRS Technologies will build on the measurements performed in the Phase I program, which will allow for higher fidelity models and a more streamlined insertion of single crystal transducers into the Navy. Dynamic and bend testing of PMN-PT and modified A and B-site doped crystals will be made to better understand the tensile strength behavior of single crystal. Self-consistent temperature-dependent ...

    SBIR Phase II 2009 Department of DefenseNavy
  2. Individualized Fatigue Management Program Technology for Trucking Operations

    SBC: PULSAR INFORMATICS, INC.            Topic: 091FM1

    Individual differences in vulnerability to sleep loss and fatigue from extended work hours and night work are a substantial problem in transportation work schedule development, fatigue risk management strategies, and prediction of performance impairment in real-world operations.  This project will deliver an individualized Fatigue Management Program (FMP) technology for trucking operations th ...

    SBIR Phase I 2009 Department of Transportation
  3. Micromechanical Assessment of Thermochemically Induced NDE Changes in Advanced Composites

    SBC: MATERIALS RESEARCH & DESIGN INC            Topic: N07177

    The Joint Strike Fighter is considering the use of organic and ceramic matrix composites for high temperature engine components. Material coupons and flight tests have shown that when these materials are exposed to high temperatures in the presence of air, salt fog, and humidity they can react chemically. The chemical reactions may cause a significant loss in composite strength even though there i ...

    SBIR Phase II 2009 Department of DefenseNavy
  4. Crack Arrest and Structural Repair of High Strength Steel Piping by In-Situ Sleeving of Nanostructural Materials

    SBC: Integran Technologies U.S.A. Inc.            Topic: 07PH1

    This proposal describes the application of a mature nanotechnology-based crack arrest / structural repair technology as a novel crack arrestor tool for high-strength pipelines. The crack arrestor would comprise a thin layer or sleeve of electrodeposited nanocrystalline material applied to the outside of the pipe either in the coating mill during fabrication or in-field during or following constru ...

    SBIR Phase I 2008 Department of Transportation
  5. Compact Laser Shearography System for Crack Detection

    SBC: Laser Technology Inc.            Topic: 05FH1

    Laser Technology Inc. (LTI) proposes a Phase II SBIR research project to further develop a Compact Shearography System, Analysis Method and Software for micro-crack detection in concrete. There is an urgent need to detect and characterize fine cracks in concrete that form because of various damage mechanisms including alkali-silicate reaction, delayed ettringite formation or frost damage. Fine s ...

    SBIR Phase II 2008 Department of Transportation
  6. Low Cost Transverse Rail Defect Detector

    SBC: Mide Technology Corporation            Topic: 02FR1

    Development of the basic EMAT based transverse rail defect detector has progressed toward finished form, as envisioned in the original solicitation. This modification is intended to produce a demonstratable version of a 2-rail detection system with automated signal interpertation. The objectives of this work are to: a. Further develop the system into a functioning 2-rail detection system, as ori ...

    SBIR Phase II 2008 Department of Transportation
  7. Public Rights-of-Way Assessment Instrumentation to Determine Accessibility

    SBC: BENEFICIAL DESIGNS INC            Topic: N/A

    Cities must perform detailed assessments of sidewalks and streets, including curb ramps, pedestrian signals, crosswalks, street furniture, and other components to determine compliance with the Public Rights-of-Way Accessibility Guidelines. However, current assessment methods are inadequate or unreasonable due to time and resources required. The objectives of this project are to: 1) develop elect ...

    SBIR Phase I 2008 Department of Transportation
  8. Structural Repair of Steel Piping by In-Situ Sleeving of Nanostructured Materials

    SBC: Integran Technologies U.S.A. Inc.            Topic: N/A

    This proposal describes the application of a mature nanotechnology-based crack arrest/structural repair technology as a novel in-field pipeline repair tool. The repair would be comprised of a thin layer or sleeve of electrodeposited nancrystalline material applied to the damaged region of the pipe in order to utilize the "crack filling" characteristic of the process. The concept proposed has alr ...

    SBIR Phase I 2008 Department of Transportation
  9. Innovative Low-cost, In-situ Consolidation Head for Complex Geometry Thermoplastic Fiber Placement

    SBC: ACCUDYNE SYSTEMS, INC.            Topic: N08135

    Accudyne proposes a SBIR program, endorsed by Sikorsky, Cytec Engineered Materials, and NASA-LaRC, to develop a cost-effective thermoplastic automated tow placement (ATP) process and demonstrate it by fabricating and testing a complex contoured skin (Phase 1) and a CH-53K rotorcraft lower cabin or ramp skin (Phase 2). The process employs in situ consolidation, avoiding the autoclave. The targete ...

    SBIR Phase I 2008 Department of DefenseNavy
  10. Innovative Approaches to the Fabrication of Composite Rotary Wing Main Rotor Blade Spars

    SBC: ACCUDYNE SYSTEMS, INC.            Topic: N08026

    This proposal will supply to NAVAIR and to rotorcraft manufacturing companies the emerging solution to their fabrication needs as it relates to the production of Rotor Blade Spars. The process and machine concept developed in Phase I will provide NAVAIR and the rotocraft manufacturing companies an automated solution to spar manufacturing. This will enable: • Low part manufacturing cost • High ...

    SBIR Phase I 2008 Department of DefenseNavy
US Flag An Official Website of the United States Government