You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Solid-state, Lightweight, Active-balance-system, Powered-by-light, (SLAP)

    SBC: ADVANCED TECHNOLOGIES GROUP, INC.            Topic: N03184

    Advanced Technologies Group, Inc. proposes a Solid-state, Lightweight, Active-balance-system, Powered-by-light, (SLAP). The SLAP balancer will reduce or eliminate drive shaft vibrations caused by rotational dynamics of the Joint Strike Fighter (JSF) lift fan drive shaft. Reduced shaft vibration will prevent drive shaft maintenance and improve support bearing life while reducing lift fan clutch w ...

    SBIR Phase II 2004 Department of DefenseNavy
  2. Innovative Gas Turbine Engine Propulsion

    SBC: AGILIS MEASUREMENT SYSTEMS, INC.            Topic: N02169

    Under this program, an evaluation will be performed to select the optimum electric power generation package to meet electrical output requirements within the confines of the propulsion system architecture - based on the results of the Phase I SBIR. Additionally, system configuration and integration issues will be addressed in an effort to quantify the following: · Document the prime power gener ...

    SBIR Phase II 2004 Department of DefenseNavy
  3. Cost-Effective Production of Piezoelectric Single Crystals

    SBC: H. C. Materials Corporation            Topic: SB031005

    : The development of cost-effective manufacturing technique for PMN-PT based piezoelectric single crystals with enhanced capabilities is critical to the achievement of the new generation of acoustic transduction devices. In Phase I, feasibility of the novel technique was demonstrated. The objective of this research project is to continue development of reducing the manufacturing costs for large-si ...

    SBIR Phase II 2004 Department of DefenseNavy
  4. Hot Gun Barrel Detector for Navy Guns

    SBC: INDUSTRIAL MEASUREMENT SYSTEMS INC            Topic: N03066

    The Navy has a critical need to measure temperatures at critical areas on the inner bore surfaces of large guns in order to insure appropriate action is taken in case of a misfire. In the case of a misfire, the gun crew must know the bore surface temperature in order to decide if they have time to safely remove the ammunition before enough heat has transferred from the hot barrel, possibly initi ...

    SBIR Phase II 2004 Department of DefenseNavy
  5. Low Drag Multi-Frequency Radome

    SBC: LINDSEY ASSOC.            Topic: N03104

    In this effort a high temperature inorganic polymer binder will be combined with quartz fabric layers to construct radomes that will be transparent at millimeter wavelengths and act as an electrical conductor at low frequencies. Electrical performance and environmental performance will be demonstrated during this effort with the use of test coupons and full sized radomes. Lindsey Associates freq ...

    SBIR Phase II 2004 Department of DefenseNavy
  6. NOVEL POLYPARAPHENYLENE COMPOSITE ABLATIVE MATERIALS FOR USE AS RAMJET COMBUSTOR INSULATION

    SBC: MISSISSIPPI POLYMER TECHNOLOGIES, INC.            Topic: N02165

    The development of lighter weight insulation with improved thermal and ablative properties is vital to the future success of ducted rocket/ramjet technology currently being developed in the United States. In Phase I, novel composite ablative materials were fabricated from Parmaxr SRP (Self-Reinforced Polymers) and carbon fibers and shown to possess numerous advantages over the current technology ...

    SBIR Phase II 2004 Department of DefenseNavy
  7. Polymer-Cased Ammunition for Small Arms and Cannon Ammunition

    SBC: MISSISSIPPI POLYMER TECHNOLOGIES, INC.            Topic: N03005

    Mississippi Polymer Technologies Inc. (MPT) proposes to develop a new generation of polymeric lightweight ammunition weighing approximately 1/3 less than existing brass ammunition. Previous efforts to develop polymer-cased ammunition have failed primarily because of problems associated with choice of case materials. During Phase I, MPT has demonstrated proof of concept overcoming these issues. D ...

    SBIR Phase II 2004 Department of DefenseNavy
  8. Development of Quantum Cascade Laser Heterostructures for Mid-Infrared (4-5 Micron) Atmospheric Transmission

    SBC: MP Technologies, LLC            Topic: N03107

    This proposal is aimed at further improving the design of quantum cascade lasers for ambient temperature free-space communication in the mid-infrared (4< lambda

    SBIR Phase II 2004 Department of DefenseNavy
  9. Non-Woven Textile Technologies: Durable Nonwoven Composite Fabrics

    SBC: NANOSYNTEX            Topic: N03162

    In Phase I, Nanosyntex demonstrated the feasibility of creating high-performance nonwoven composite fabrics that showed superior strength and comfort properties over current woven military uniform fabrics. The main objective of this Phase II SBIR project is to further optimize the design and structure of these composite fabrics through advanced research studies to specifically enhance abrasion res ...

    SBIR Phase II 2004 Department of DefenseNavy
  10. Advanced Truck for High Speed Freight Operations

    SBC: Sharma & Associates, Inc.            Topic: N/A

    During Phase I of the project, Sharma & Associates, Inc. developed a concept for a high speed freight truck intended for 70-ton, regular freight and bi-modal operation at speeds up to 150 mph. The truck uses a rigid frame and an independent, compliant, primary suspension for its basic architecture. Constant contact side-bearings and yaw dampers were also added to improve dynamic performance. Ve ...

    SBIR Phase II 2004 Department of Transportation
US Flag An Official Website of the United States Government