You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Hermetic Seals for Chemical/Biological Protective Garments

    SBC: CREARE LLC            Topic: CBD13109

    Interfaces on existing military chemical/biological protection garments are not designed to fully eliminate macroscopic and microscopic air gaps at folds, fabric surfaces, or hook-and-loop closures, and thus do not provide a hermetic barrier against exposure. Creare proposes to develop a hermetic garment closure system that seals macroscopic and microscopic gaps at interfaces and closures and pro ...

    SBIR Phase II 2014 Department of DefenseOffice for Chemical and Biological Defense
  2. A Low-Cost, High-Performance Colloidal Quantum Dot LWIR FPA for Hyperspectral Imaging

    SBC: SIVANANTHAN LABORATORIES, INC.            Topic: CBD13105

    The primary goal of this proposed work is to develop a long wavelength infrared (LWIR) colloidal quantum dot (CQD)-based focal plane array (FPA) and show its feasibility when used in a camera system and a hyperspectral imaging system. Phase I results cumulated in the first-ever synthesis of photoresponsive LWIR CQDs and CQD-based photodetectors at the single device level operating at room temperat ...

    SBIR Phase II 2014 Department of DefenseOffice for Chemical and Biological Defense
  3. Design Automation Software for Biomimetic Surface Presentation with DNA Origami

    SBC: PARABON NANOLABS, INC.            Topic: CBD12103

    A development program is proposed for a design automation software package that enables the generation of complex surfaces, with user defined or automated definition of point charge and hydrophobic/hydrophilic properties, using DNA origami as a presentation substrate. Building upon Parabons existing software for DNA origami design, this project will result in software that can be used to design a ...

    SBIR Phase II 2014 Department of DefenseOffice for Chemical and Biological Defense
  4. Six-Axis Force-Torque Transducer for Mars 2018 Mission

    SBC: ATI Industrial Automation, Inc.            Topic: S502

    A transducer element that is hearty enough for a Mars lander mission needs to be developed so that a six-axis force and torque transducer is possible. The technical objectives are: 1. A transducer element capable of surviving temperatures from -135?C to +125?C. 2. The transducer element in objective 1 with temperature compensation to minimize span and offset drift from -80?C to +70?C. 3. The tran ...

    SBIR Phase II 2014 National Aeronautics and Space Administration
  5. HybridSil Icephobic Nanocomposites for Next Generation Aircraft In-Flight Icing Measurement and Mitigation

    SBC: Nanosonic Inc.            Topic: A102

    The purpose of this SBIR program is to adapt NanoSonic's HybridSil® nanocomposites and combine high erosion resistance, low ice adhesion, and passive anti-icing functionality with Metal Rubber sensor technology to enable in-flight icing measurement and mitigation for next generation aircraft. During Phase I, NanoSonic successfully demonstrated novel sensor design concepts coupled with HybridSi ...

    SBIR Phase II 2014 National Aeronautics and Space Administration
  6. Cost Reduction of IMM Solar Cells by Recycling Substrates Using Wet Chemical Etching

    SBC: Microlink Devices, Inc.            Topic: H804

    The goal of the program is to reduce the cost of substrate reclaim for high-efficiency solar cells fabricated by an epitaxial lift-off (ELO) process, and to increase the number of reuse cycles for a given substrate. If successful, this will result in a reduction in the cost of GaAs-based multi-junction solar cells, in which the cost of the substrate accounts for approximately 50% of the total cos ...

    SBIR Phase II 2014 National Aeronautics and Space Administration
  7. Microhydrogel Depot for Sustained Delivery of Prophylactic Bioscavenger

    SBC: Luna Innovations Incorporated            Topic: CBD13107

    Countering the threat of intoxication by organophosphorus nerve agents is an important mission for homeland security. Currently, the most promising strategy is to bioscavenge the agents using injectable plasma-derived butyrylcholinesterase (BuChE) that has low substrate specificity and may offer a broad spectrum protection against OP agents. Human plasma-derived BuChE at 400mg IV dose is prophylac ...

    SBIR Phase II 2014 Department of DefenseOffice for Chemical and Biological Defense
  8. A Miniature Autoinjector for Multicomponent Drugs and Vaccines

    SBC: CREARE LLC            Topic: CBD13106

    Chemical, biological, or toxin attacks in military and civilian settings are a serious and growing concern. Standard first aid for exposure to some chemical warfare agents and toxins includes the immediate administration of relevant antidotes using an autoinjector. When an attack occurs, pre-filled autoinjectors must be immediately available and thus highly portable, and they must be suitable fo ...

    SBIR Phase II 2014 Department of DefenseOffice for Chemical and Biological Defense
  9. Additive Friction Stir Deposition of Aluminum Alloys and Functionally Graded Structures

    SBC: AEROPROBE CORPORATION            Topic: H502

    State-of-the-art additive manufacturing technologies for metal parts have evolved primarily around powder metallurgy and fusion welding-based processes. These processing methodologies yield parts with inferior mechanical and physical properties as compared to wrought metal of the same composition. Additionally, the production rates for even the fastest processes are relatively low, the part enve ...

    SBIR Phase II 2014 National Aeronautics and Space Administration
  10. A Novel Plasma-Based Compressor Stall Control System

    SBC: CREARE LLC            Topic: A308

    Modern aircraft gas turbine engines utilize highly loaded airfoils in both the compressor and turbine to maximize performance while minimizing weight, cost, and complexity. However, high airfoil loading increases the likelihood of flow separation at lower mass flow rates. Dielectric Barrier Discharge (DBD) plasma actuators have been shown to be a very promising technique for compressor stall con ...

    SBIR Phase II 2014 National Aeronautics and Space Administration
US Flag An Official Website of the United States Government