List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

Displaying 1 - 10 of 3219 results
  1. Direct Performance Evaluation of Additive Manufacturing Process Plans

    SBC: INTACT SOLUTIONS INC.            Topic: None

    Additive manufacturing is steadily advancing towards fulfilling its promise of customized and on-demand production of functional parts. However, performance of as-manufactured parts can differ significantly from the as-designed parts because the as-manufactured geometry differs from the as-designed geometry and the asmanufactured material properties are not known. Attempts to predict performance o ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  2. Developing Silicon Nanowire Sensors to Measuring Host-Cell Proteins at a Biomanufacturing Line

    SBC: Advanced Silicon Group            Topic: None

    Our biosensor is made of silicon nanowire arrays functionalized with antibodies to measure the concentration of specific proteins. In this grant we will take a sensor that has been demonstrated for use in measuring a set of generic host cell proteins and we will apply the sensor to measure a set of proteins for a specific cell line. In doing so, we will demonstrate the utility of our sensor to be ...

    SBIR Phase II 2019 Department of CommerceNational Institute of Standards and Technology
  3. Blast Overpressure Omnidirectional Measurement Device

    SBC: MAINSTREAM ENGINEERING CORPORATION            Topic: A18078

    Mainstream proposes developing a blast overpressure omnidirectional measurement (BOOM) device that detects, records, and transmits captured data for blast events experienced by individual personnel. The BOOM device is composed of a microcontroller that collects, stores, and transmits data collected from several miniature pressure transducers placed on personnel. The sensors enable capture of the p ...

    SBIR Phase I 2019 Department of DefenseArmy
  4. DEVELOPMENT OF A NOVEL TRANSMISSION FOR HELICOPTER APPLICATIONS

    SBC: VISHWA ROBOTICS AND AUTOMATION LLC            Topic: A16018

    US Army utilizes a wide range of vehicles across ground and air platforms where mechanical transmissions are used to transmit power from the engine to the drive shaft. Gears are used to create a torque and speed conversion with mechanical contact between the gear teeth surfaces. Lubrication is necessary to create a protective film between rolling and sliding surfaces as well as provide sufficient ...

    SBIR Phase II 2019 Department of DefenseArmy
  5. Waterproofing Cargo Airdrop Equipment

    SBC: RESODYN CORPORATION            Topic: A16114

    The U.S. Army is interested in the development of innovative coating technologies to allow current U.S. Army airdrop related hardware and equipment to survive fresh and salt water operations with increased reliability and without damage and significant maintenance impact. Resodyn Corporation proposes for development a durable, moisture-impermeable, thermoplastic coating material to address the U.S ...

    SBIR Phase II 2019 Department of DefenseArmy
  6. Signal Processing at Radio Frequency (RF) for Position Navigation & Timing Co-Site Interference

    SBC: Metamagnetics Inc.            Topic: A17039

    Numerous operations in an increasingly congested electromagnetic spectrum, intensify demand for data at the tactical edge, and the diminishing extent of electromagnetic spectrum provisioned for the military has resulted in the need for advanced technologies to mitigate Global Positioning System (GPS) interference due to co-site interference and C4ISR. Metamagnetics proposes a powerful and adaptabl ...

    SBIR Phase II 2019 Department of DefenseArmy
  7. CMOS Compatible Deposition of Multi-Ferroic Films for Tunable Microwave Applications

    SBC: Winchester Technologies, LLC            Topic: A17019

    Built upon the progress in Phase I period, Winchester Technologies, LLC proposes to investigate practical magnetoelectric antennas during the Phase II period for different applications. State of the art antennas suffer from three major open challenges: (1) large antenna size, (2) antenna impedance mismatch; (3) ground plane effect. This is because state of the art antennas are based on oscillating ...

    SBIR Phase II 2019 Department of DefenseArmy
  8. Lightweight, Durable, Low-Cost Recuperators Designed for Integration with Small Turbo-generators for Future Army Unmanned Aerial Systems

    SBC: Florida Turbine Technologies Inc.            Topic: A17001

    FTT proposes to design, build, and test an advanced light-weight, low-cost, and durable additively manufactured recuperator.Testing will be first performed in a component rig with similar engine conditions to increase TRL to 5.Following successful completion of the component rig, FTT will mate the recuperator up with a 5KW turbogenerator and run the assembly at FTT Small Engine Test Facility in or ...

    SBIR Phase II 2019 Department of DefenseArmy
  9. FTL's FASCI, Forward Area Suspended Contaminant Identifier, Field Instrumentation to measure, quantify, and characterize fuel contaminants

    SBC: FTL Labs Corporation            Topic: A17116

    To avoid machine failure, diesel engine hardware manufacturers recommend limiting fuel contamination particles based on number and size distribution. Work performed by TARDEC has developed limits for particulate and free water contamination in fuel utilizing light obscuration particle counting; however, this approach is unable to differentiate between solid particulates, free water droplets, and a ...

    SBIR Phase II 2019 Department of DefenseArmy
  10. High Performance, Insensitive Munition Compliant, Structural Combustible Cartridge Case for Ammunitions

    SBC: Physical Sciences Inc.            Topic: A18013

    Physical Sciences Inc. proposes to demonstrate and quantify a unique high performance, insensitive munition compliant, structural combustible cartridge case for ammunitions that would significantly augment the ballistic performance. This new formulation will increase the ballistic energy, impetus, and muzzle velocity, while simultaneously eliminating combustion residue and providing insensitivity ...

    SBIR Phase I 2019 Department of DefenseArmy

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government