Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until June, 2020.

  1. Individualized Fatigue Management Program Technology for Trucking Operations

    SBC: PULSAR INFORMATICS, INC.            Topic: 091FM1

    Individual differences in vulnerability to sleep loss and fatigue from extended work hours and night work are a substantial problem in transportation work schedule development, fatigue risk management strategies, and prediction of performance impairment in real-world operations.  This project will deliver an individualized Fatigue Management Program (FMP) technology for trucking operations th ...

    SBIR Phase I 2009 Department of Transportation
  2. Lightweight, Compact Atmospheric Gas Sensor

    SBC: SYNKERA TECHNOLOGIES INC            Topic: SOCOM08005

    The objective of the SBIR project is to develop a lightweight and compact atmospheric and trace gas sensors that can be safely used within the Scope of Certification boundary to provide real-time monitoring of CO2, O2 and trace contaminant levels in manned compartments or within piping systems onboard submersibles. .Synkera has extensive experience at development of sensor technologies for indust ...

    SBIR Phase II 2009 Department of DefenseSpecial Operations Command
  3. Series Resistance Reduction in Tunable Radio Frequency (RF) Capacitors

    SBC: PARATEK MICROWAVE, INC.            Topic: DMEA092001

    By attention to lattice parameter matching, thermal expansion coefficient mismatch reduction and composition of conducting epitaxial detemined.

    SBIR Phase I 2009 Department of DefenseDefense Microelectronics Activity
  4. Novel Nanomaterials for Environmental Protection of Special Operations Divers

    SBC: TDA Research, Inc.            Topic: SOCOM09001

    Environmental protection is a critical need for special operations forces which dive in cold water during their missions. Thermally protective diving suit must be able to provide significant thermal barriers as well as withstand high compressive loads when underwater. Current diver wet suits and dry suits are limited by their materials of construction in the degree of thermal protection they can ...

    SBIR Phase I 2009 Department of DefenseSpecial Operations Command
  5. Low Visibility Decoy Flare

    SBC: GENERAL SCIENCES INC            Topic: SOCOM09002

    Low visibility rotary aircraft decoys are needed to protect vehicles against heat seeking missile attacks without illuminating the target which exposes the aircraft to small arms fire and potentially compromising the mission. The novel approach to this challenge is to produce a decoy which emits only in the bands of interest utilizing techniques such as containment and composition selection to op ...

    SBIR Phase I 2009 Department of DefenseSpecial Operations Command
  6. High-Speed Dynamic 3D Surface Mapping System

    SBC: Conrad Technologies, Inc.            Topic: N/A

    Conrad Technologies, Inc. (CTI) proposes a non-contact, dynamic 3D position sensor based on optical triangulation using multiple radiating LED targets to measure intrusion of an automobile structure into the occupant compartment during full-scale crash tests. CTI has significant experience developing non-contact measurement instruments. CTI has developed a Motion Imaging and Tracking Acquisition ...

    SBIR Phase I 2002 Department of Transportation
  7. FABRICATING STRUCTURAL ELEMENTS, SUCH AS I-BEAMS, FROM FIBERREINFORCED COMPOSITE MATERIALS.

    SBC: The Cumagna Corpon            Topic: N/A

    FABRICATING STRUCTURAL ELEMENTS, SUCH AS I-BEAMS, FROM FIBERREINFORCED COMPOSITE MATERIALS. THESE ELEMENTS ARE EXPECTEDTO BE EXTREMELY STRONG, ONE-FOURTH THE DENSITY OF STEEL, ANDTO PERMIT CONSIDERABLE SAVINGS IN THE COST OF ERECTION, MAINTENANCE, AND REPLACEMENT OF BRIDGES, ETC. PHASE I WILL PRODUCE, TEST, AND ANALYZE I-BEAMS FABRICATED FROM SEVERAL MAGNAWEAVE CONSTRUCTIONS (WEAVE GEOMETRIES); TH ...

    SBIR Phase I 1983 Department of Transportation
  8. Evaluation of Composite Joints in General Aviation Structures

    SBC: Materials Sciences LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase II 2002 Department of Transportation
  9. Evaluation of Composite Joints in General Aviation Structures

    SBC: Materials Sciences LLC            Topic: N/A

    During the Phase I program, MSC demonstrated a powerful new software tool designed for the analysis of bonded joints in General Aviation (GA) aircraft. The tool can handle the complex geometry and boundary conditions found in typical joints, and has been shown to be exceptionally accurate. An easy-to-use front end to the code was also demonstrated. In addition, Materials Sciences Corporation (M ...

    SBIR Phase I 2002 Department of Transportation
  10. A Low-Cost In-flight Deicing System for Aircraft

    SBC: CREARE LLC            Topic: N/A

    The proposed innovation is a deicing system for aircraft leading edges using a high-efficiency, electrically actuated thin-film elastomer. The entire aircraft industry needs this technology to improve safety while minimizing the overall impact on aircraft weight and fuel consumption. We propose to use a low-cost, electrically actuated thin-film elastomer to break the ice bond in a manner similar ...

    SBIR Phase I 2002 Department of Transportation
US Flag An Official Website of the United States Government