You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

  1. An Optical Imaging System to Characterize Mechanical Deformation at Microscopic Length Scale

    SBC: Additive Manufacturing Innovations LLC            Topic: 90

    Additive Manufacturing Innovations LLC (AM-Innov) in collaboration with Clarkson University and Naval Research Laboratory (NRL) proposes a new optical imaging system to characterize microscopic deformation of materials. The system, named as a Mechanical Testing at Microscale system (MT@micro), uses a micro-tensile testing device to mechanically load the specimen uniaxially and an optical imaging p ...

    SBIR Phase I 2020 Department of CommerceNational Institute of Standards and Technology
  2. Standardizing Grease Sampling and Characterization By Automated Online Device

    SBC: Poseidon Systems, LLC            Topic: 90

    Scheduled grease sampling is one of the more reliable methods for detecting mechanical issues within machinery. Offline laboratory‐based analysis of the grease can indicate component failures, such as spalling via high concentrations of ferrous particulates. However, consistency, costs, and frequency of sampling are less than ideal. Manually collecting grease samples can put personnel in danger ...

    SBIR Phase I 2020 Department of CommerceNational Institute of Standards and Technology
  3. High Throughput, High-Pressure Small-Angle Neutron Scattering Sample Environment

    SBC: STF Technologies LLC            Topic: 90

    We address a need of the neutron user community by creating a minimum viable prototype of the only high-throughput hydrostatic pressure small angle neutron scattering sample environment (HTHP-SANS-SE). Our HTHP-SANS-SE will greatly improve the ease of use and reliability of measurements under extreme environments, thereby increasing throughput on the beamline and expanding feasibility. Current HP- ...

    SBIR Phase I 2020 Department of CommerceNational Institute of Standards and Technology
  4. Nanomachine Device for Semiconductor Process Control Monitoring

    SBC: Xallent LLC            Topic: None

    Conventional characterization and test methods are increasingly ineffective when applied to structures less than 100 nanometers, causing challenges across R&D, process control and failure analysis. An increasing number of subtle defects become prominent drivers of failure as device size and operating margins decrease, e.g., processing anomalies in thin gate oxides, substrate problems related to do ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  5. IF Conversion System for High-Bandwidth Multiplexed Sensors Arrays

    SBC: Alphacore, Inc.            Topic: None

    Alphacore will develop an Intermediate Frequency (IF) Conversion System for High-Bandwidth Multiplexed Sensors Arrays for Phase II of NIST's 2018 soliciation for Exploratory Measurement Science Topic 9.04.02.68.The proposing team has already successfully developed and evaluated a prototype board in Phase I.The goal in Phase II is therefore to achieve three primary objectives:1) Optimize the design ...

    SBIR Phase II 2019 Department of CommerceNational Institute of Standards and Technology
  6. IF Conversion System for High-Bandwidth Multiplexed Sensors Arrays

    SBC: Alphacore, Inc.            Topic: NA

    Alphacore will develop an Intermediate Frequency (IF) Conversion System for High-Bandwidth Multiplexed Sensors Arrays for NIST’s 2018 solicitation for Exploratory Measurement Science Topic 9.04.02.68. The proposing team has already successfully developed and evaluated a similar printed-circuit board (PCB)-based system for NIST (ROACH2 BLAST-TNG, refer section 1.2). The goal in Phase I is therefo ...

    SBIR Phase I 2018 Department of CommerceNational Institute of Standards and Technology
  7. Continuous Learning for Additive Manufacturing Processes Through Advanced Data Analytics

    SBC: Senvol LLC            Topic: NA

    Additive manufacturing (AM) is a promising manufacturing technique for end-use parts that can solve challenges for American manufacturers in many industries, e.g. aerospace, defense, automotive, energy, and healthcare. However, despite the potential that AM offers, the rate of AM adoption in industry is very slow. This is because AM suffers from low repeatability and quality consistency issues, wh ...

    SBIR Phase I 2018 Department of CommerceNational Institute of Standards and Technology
  8. HQ-55 VTOL UAS for Ship Based Operation

    SBC: Latitude Engineering, LLC            Topic: 832

    TECHNICAL ABSTRACT: The Hybrid Quadrotor concept, developed by Latitude Engineering, combines the high power density of electric motors and propellers with the high energy density of a piston engine and liquid fuel. Together, each technology enables maximum performance in HQ's two regimes of flight: the electric system is responsible for lift while hovering (high power, short endurance), and the g ...

    SBIR Phase II 2018 Department of CommerceNational Oceanic and Atmospheric Administration
  9. A Location-based Weather Threat Tracking and Notification System

    SBC: CFD Research Corporation            Topic: 834

    TECHNICAL ABSTRACT: CFDRC proposes the creation of an innovative location-based threat tracking and notification system to allow users to receive hazardous weather messages from the NWS with their call to action, allow users to receive custom-tailored messages about threats, and visualize relevant weather information within their area. The focus is on a tool that allows this information to be comm ...

    SBIR Phase I 2018 Department of CommerceNational Oceanic and Atmospheric Administration
  10. HQ-55 VTOL UAS for Ship Based Operation

    SBC: L3 Latitude, LLC            Topic: 832

    The Hybrid Quadrotor concept, developed by Latitude Engineering, combines the high power density of electric motors and propellers with the high energy density of a piston engine and liquid fuel. Together, each technology enables maximum performance in HQ's two regimes of flight: the electric system is responsible for lift while hovering (high power, short endurance), and the gas engine gives long ...

    SBIR Phase I 2017 Department of CommerceNational Oceanic and Atmospheric Administration
US Flag An Official Website of the United States Government