List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for the given year is not complete until April of the following year. Annual Reports data is a snapshot of agency reported information for that year and hence might look different from the live data in the Awards Information charts.

  1. Direct Performance Evaluation of Additive Manufacturing Process Plans

    SBC: INTACT SOLUTIONS INC.            Topic: None

    Additive manufacturing is steadily advancing towards fulfilling its promise of customized and on-demand production of functional parts. However, performance of as-manufactured parts can differ significantly from the as-designed parts because the as-manufactured geometry differs from the as-designed geometry and the asmanufactured material properties are not known. Attempts to predict performance o ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  2. Nanomachine Device for Semiconductor Process Control Monitoring

    SBC: Xallent LLC            Topic: None

    Conventional characterization and test methods are increasingly ineffective when applied to structures less than 100 nanometers, causing challenges across R&D, process control and failure analysis. An increasing number of subtle defects become prominent drivers of failure as device size and operating margins decrease, e.g., processing anomalies in thin gate oxides, substrate problems related to do ...

    SBIR Phase I 2019 Department of CommerceNational Institute of Standards and Technology
  3. Continuous Learning for Additive Manufacturing Processes Through Advanced Data Analytics

    SBC: Senvol LLC            Topic: NA

    Additive manufacturing (AM) is a promising manufacturing technique for end-use parts that can solve challenges for American manufacturers in many industries, e.g. aerospace, defense, automotive, energy, and healthcare. However, despite the potential that AM offers, the rate of AM adoption in industry is very slow. This is because AM suffers from low repeatability and quality consistency issues, wh ...

    SBIR Phase I 2018 Department of CommerceNational Institute of Standards and Technology
  4. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: Senvol LLC            Topic: DLA18A001

    The Department of Defense (DoD) has a demand for out-of-production parts to maintain mission readiness of various weapons platforms. Additive manufacturing (AM) is an exciting and promising manufacturing technique that can make out-of-production parts and holds the potential to solve supply chain issues, such as high costs (i.e. for low-volume parts) and sole sourcing risks. The ability of AM to s ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  5. Rotorcraft Fuel Bladder Weight and Total Ownership Cost Reduction

    SBC: Response Technologies, LLC            Topic: DLA182001

    Response Technologies will attempt to qualify to MIL-DTL-27422Fs phase I performance testing criteria for thefuel cell test cubes[Class BSemi rigid or self-supporting fuel construction, Type ISelf-sealing, and Protection Level CFull self-sealing against 50 caliber and partial self-sealing against 14.5 mm] .Response Technologiesuses an additive manufacturing process that initially creates a textile ...

    SBIR Phase I 2018 Department of DefenseDefense Logistics Agency
  6. Additively Manufactured Inflatable Hulls- Improved Survivability- 20% Total Ownership Cost Reduction

    SBC: Response Technologies, LLC            Topic: DLA152001

    Seam failures of flexible inflatable hulls is the primary reason for failures of military RHIBS and CRCs.These failures are a result of the current manufacturing methods being used, and which have been in place for over fifty years.Whats more, the manufacturing methods and fragmented supply chain of these hulls result in very long and unreliable lead times.These shortcomings impact the survivabili ...

    SBIR Phase II 2018 Department of DefenseDefense Logistics Agency
  7. High Temperature High Resolution in-situ Differential Pressure Sensor

    SBC: Innoveering, LLC            Topic: NA

    Chemical manufacturers require high accuracy/high sensitivity pressure sensors to efficiently monitor the various manufacturing systems and processes in the chemical plant, to ensure any changes proceed in a safe and reliable manner, adhering to expected standards and practices. NIST also has a need for highly accurate pressure measurements, especially determining the thermo-physical properties of ...

    SBIR Phase II 2017 Department of CommerceNational Institute of Standards and Technology
  8. Economically Recovering Rare Earth Materials

    SBC: XYLON TECHNICAL CERAMICS INC.            Topic: DLA161003

    This Phase II SBIR project seeks to develop and commercialize methods for recycling rare earth materials from strategic waste streams. Rare earth materials are critical for a broad range of technologies. Important industrial sectors such as defense, manufacturing, energy, transportation, and electronics all utilize rare earths in abundance. There are currently a limited number of economically v ...

    SBIR Phase II 2017 Department of DefenseDefense Logistics Agency
  9. High Temperature High Resolution in-situ Differential Pressure Sensor

    SBC: Innoveering, LLC            Topic: 90105

    Chemical manufacturers require high accuracy and high sensitivity pressure sensors to efficiently monitor the various manufacturing systems and processes in the chemical plant, to ensure any changes proceed in a safe and reliable manner, adhering to expected standards and practices. In addition, NIST has a need for highly accurate absolute and differential pressure measurements, especially for det ...

    SBIR Phase I 2016 Department of CommerceNational Institute of Standards and Technology
  10. GlobalSense: A New Atmospheric Observing System Featuring Innovative Airborne Probes

    SBC: MANO NANOTECHNOLOGIES INC            Topic: 861

    The underlying framework for modern-day weather forecasting is numerical weather prediction (NWP). Even the current and planned weather observing platforms leave gaps that are insufficient to meet the requirements of NWP. Mano Nanotechnologies, Inc. proposes to commercialize a new environmental sensing system, known as “GlobalSense”, which will enable transformational forecast improvements by ...

    SBIR Phase II 2016 Department of Commerce

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government