You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. A collaboration to develop a commercialization path or a Photonic Memory Controller Module (P-MCM)

    SBC: PLCC2 LLC            Topic: 04a

    As computational density for high-performance computing and big-data services continues to scale, performance scalability of next generation computing systems is becoming increasingly constrained by limitations in memory access, power dissipation and chip packaging. The processor-memory communication bottleneck, a major challenge in current multicore processors due to limited pin-out and power bud ...

    STTR Phase I 2017 Department of Energy
  2. A Concrete Additive Manufacturing Process for Fixed and Floating Wind Turbine Foundations and Towers

    SBC: JC Solutions            Topic: 14b

    Tall towers and foundations for modern offshore and land-based wind turbines are too large to transport over roads or rail due to their extremely large dimensions. Existing “one-off” on-site construction methods are too expensive, and are too slow for manufacturing foundations and towers in the large numbers needed, especially for offshore components manufactured in ports with limited lay-down ...

    STTR Phase I 2018 Department of Energy
  3. Additive Manufacturing of Scalable 3D Resonators

    SBC: Global Research and Development Inc.            Topic: 29b

    This proposal is submitted in response to the SBIR/STTR Office of Science related to Quantum Information Science (QIS) Supporting Technologies. There is the need for fabrication techniques for scalable 3D Superconducting Radio Frequency (SRF) Structures for Quantum Information Systems. In this proposal we will develop an additive manufacturing approach to developing superconducting 3D microwave re ...

    STTR Phase I 2018 Department of Energy
  4. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  5. Advanced Membranes for CO2 Capture from Existing Coal-fired Power Plants

    SBC: Nextech Materials, Ltd.            Topic: 24a

    Coal is an abundant source of energy in the USA, but is not currently utilized effectively. Recently, the DOE has begun a carbon sequestration program is to develop advanced CO2 capture and compression technology for existing coal-fired plants with increased efficiency with no more than a 35% increase in the cost of electricity. This will require new approaches and technologies to be successful. N ...

    STTR Phase I 2010 Department of Energy
  6. Advanced Morphing Moulage for Medical Training (AMM-MT)

    SBC: Vcom3D, Inc.            Topic: DHA17A002

    For this Phase I SBIR proposal, Vcom3D proposes to design advanced medical moulage that accurately simulates the progression of an injury or pathology by morphing through a series of clinical states to enable learners to confirm the progression of the wound and to determine whether iatrogenic errors or pathologies occurred duing treatment. The physical morphing moulage may be applied to medical m ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  7. A Mesh Free Framework for Mechanical Simulations of Microstructure Data Files

    SBC: CFD Research Corporation            Topic: 07a

    The Exascale Computing Project is tasked to develop the next generation of high performance computing systems capable of computing at 50 to 100 times faster than current HPC systems. Computing at this extreme-scale will significantly enhance the value of materials modeling and simulation to basic materials research and engineering In particular, computing at the extreme scale will enable a higher ...

    STTR Phase I 2019 Department of Energy
  8. A microfluidic ice nucleating particle counter for continuous measurements from small aerial platforms

    SBC: HANDIX SCIENTIFIC Inc.            Topic: 23a

    Quantifying atmospheric aerosol, clouds and precipitation processes are critical needs for understanding and interpreting Earth’s changing energy budget, is a DOE objective, and is of broader benefit to the public. Specifically, the formation of ice in the atmosphere depends on the nature and abundance of ice nucleating particles, and has major implications for precipitation and cloud interactio ...

    STTR Phase I 2018 Department of Energy
  9. Amplifiers for High Repetition Rate Diode-Pumped Ultra-Intense Femtosecond Lasers

    SBC: XUV Lasers, Inc.            Topic: 25c

    The problem being addressed is the development of high intensity ultrashort pulse lasers, in recognition that today’s ultra-high intensity lasers are limited to repetition rates of < 10 Hz. Technical solutions are sought to enable the generation of high energy (joule-level) laser pulses that can be focused to highly relativistic intensity at high repetition rates (100-1000 Hz). The proposed proj ...

    STTR Phase I 2019 Department of Energy
  10. A Multi-physics Analysis Capability for Engine Materials

    SBC: Sunergolab Inc.            Topic: 03b

    Computer-aided Engineering software that apply the Finite Element Method to perform a multi-physics analysis have received widespread acceptance for traditional macro-scale material systems. Challenges persist in the modeling of complex coupled processes in environmental/thermal barrier coatings (E/TBCs) used to protect substrate material against the corrosive environment in the hot section parts ...

    STTR Phase I 2019 Department of Energy
US Flag An Official Website of the United States Government