You are here
Award Data
The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.
Download all SBIR.gov award data either with award abstracts (290MB)
or without award abstracts (65MB).
A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.
The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.
-
Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.
SBC: ARCTOS Technology Solutions, LLC Topic: DLA18A001Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...
STTR Phase I 2018 Department of DefenseDefense Logistics Agency -
Principled Design of an Augmented Reality Trainer for Medics
SBC: UNVEIL LLC Topic: DHP17A003Augmented reality (AR) offers the ability to enhance existing combat medic training by including perceptual cues and adaptive training elements to traditional simulation-based training using manikins. Unveil has developed a training system called the Macrocognitive AR Trainer (MART). MART is designed to foster the development of macrocognitive skills (e.g., sensemaking, assessment skills, mental m ...
STTR Phase II 2018 Department of DefenseDefense Health Agency -
CORC; Cable Based High Field Hybrid Magnets for Future Colliders
SBC: ADVANCED CONDUCTOR TECHNOLOGIES LLC Topic: 26b"The next generation of very high field accelerator magnets (20 T or more) are expected to be made with high-temperature superconductors (HTS) along with conventional low-temperature superconductors (LTS) to reduce cost. The operation and protection of these magnets becomes very challenging particularly if the HTS coils are made with the tapes and operate at a much lower current than the LTS coils ...
STTR Phase II 2018 Department of Energy -
Scaleup of a Combined Spray Pyrolysis and Fluidized-bed Reactor Method for the Production of High Performing Layered Nickel- rich Cathode Materials as a Continuous Process
SBC: HAZEN RESEARCH, INC. Topic: 14aTo increase the utilization of electric vehicles, the US Department of Energy is seeking to reduce the cost of electric vehicle batteries to less than $125/kWh by 2022. To achieve this goal, the costs of cathode materials, which account for approximately 30% of the cost of vehicle batteries, must be reduced significantly. To address the challenge of lowering the costs of advanced lithium battery c ...
STTR Phase II 2018 Department of Energy -
Dynamic virtual moulage based on thin film adhesive displays
SBC: ARCHIE MD INC. Topic: DHA17A002Providing Army combat medics with meaningful experience in treatment of battlefield injuries is a particular challenge. Moulage has the potential to assist in acquiring what could otherwise be very hard-to-come-by preparatory experience for distressing real-life emergencies medics and soldiers may encounter in the field. However, current approaches to moulage are limited in their ability to reflec ...
STTR Phase II 2018 Department of DefenseDefense Health Agency -
Additive Manufacturing of Scalable 3D Resonators
SBC: GLOBAL RESEARCH & DEVELOPMENT INC Topic: 29bThis proposal is submitted in response to the SBIR/STTR Office of Science related to Quantum Information Science (QIS) Supporting Technologies. There is the need for fabrication techniques for scalable 3D Superconducting Radio Frequency (SRF) Structures for Quantum Information Systems. In this proposal we will develop an additive manufacturing approach to developing superconducting 3D microwave re ...
STTR Phase I 2018 Department of Energy -
Variable Flux Machines for Hybrid Electric Vehicles
SBC: ASYMMETRIC TECHNOLOGIES, LLC Topic: 13bThe majority of hybrid electric vehicles and electric vehicles (HEV/EV) products use interior permanent magnet (IPM) synchronous machines for traction purpose due to the efficiency and power density consideration. IPM machines use high energy density rare earth based magnet materials such as neodymium and dysprosium. Variable flux (VF) machines using abundant and cheaper soft magnets such as AlNiC ...
STTR Phase I 2018 Department of Energy -
Low-cost and Flexible Transparent Electrodes Based on Ag–ZTOF (Zn–Sn–O–F) Amorphous Composites Through Ink-jet Printing
SBC: HAZEN RESEARCH, INC. Topic: 09bSn-doped In2O3 (ITO) is the industry standard and most widely used transparent conducting electrode (TCE) because of its good electrical and optical properties. However, ITO has a number of disadvantages: ITO is not a suitable TCE for next-generation, high-efficiency, flexible OLEDs, because of its inappropriate work function, difficulty in creating desired patterns, low stability, delaminantion d ...
STTR Phase I 2018 Department of Energy -
Nanoparticle Catalytic Discovery using Machine Learning Models with Chemisorption Inputs
SBC: BIENA TECH LLC Topic: 06aThe mechanisms guiding nanocatalysis are poorly understood and extremely hard to model. Proposed effort attempts to provide a machine learning based platform that would guide the design of nanocatalytic materials for a variety of applications, beginning with the use of case of chloro-organic contaminant remediation. The current approaches either use conventional molecular dynamics coupled with ab ...
STTR Phase I 2018 Department of Energy -
A Concrete Additive Manufacturing Process for Fixed and Floating Wind Turbine Foundations and Towers
SBC: JC Solutions Topic: 14bTall towers and foundations for modern offshore and land-based wind turbines are too large to transport over roads or rail due to their extremely large dimensions. Existing “one-off” on-site construction methods are too expensive, and are too slow for manufacturing foundations and towers in the large numbers needed, especially for offshore components manufactured in ports with limited lay-down ...
STTR Phase I 2018 Department of Energy