You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. A Concrete Additive Manufacturing Process for Fixed and Floating Wind Turbine Foundations and Towers

    SBC: JC Solutions            Topic: 14b

    Tall towers and foundations for modern offshore and land-based wind turbines are too large to transport over roads or rail due to their extremely large dimensions. Existing “one-off” on-site construction methods are too expensive, and are too slow for manufacturing foundations and towers in the large numbers needed, especially for offshore components manufactured in ports with limited lay-down ...

    STTR Phase I 2018 Department of Energy
  2. Additive Manufacturing of Scalable 3D Resonators

    SBC: GLOBAL RESEARCH & DEVELOPMENT INC            Topic: 29b

    This proposal is submitted in response to the SBIR/STTR Office of Science related to Quantum Information Science (QIS) Supporting Technologies. There is the need for fabrication techniques for scalable 3D Superconducting Radio Frequency (SRF) Structures for Quantum Information Systems. In this proposal we will develop an additive manufacturing approach to developing superconducting 3D microwave re ...

    STTR Phase I 2018 Department of Energy
  3. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  4. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    This Phase II project aims to assemble the key set of sensor modalities that are needed to reliably view the key process anomalies and properties of laser powder bed fusion. The research team will down-select from the Phase I sensors investigated and integrate the sensors into a sensor fusion software package that facilitates data collection and synchronization, and eventually feedback control of ...

    STTR Phase II 2019 Department of DefenseDefense Logistics Agency
  5. Advanced Membranes for CO2 Capture from Existing Coal-fired Power Plants

    SBC: NEXTECH MATERIALS, LTD.            Topic: 24a

    Coal is an abundant source of energy in the USA, but is not currently utilized effectively. Recently, the DOE has begun a carbon sequestration program is to develop advanced CO2 capture and compression technology for existing coal-fired plants with increased efficiency with no more than a 35% increase in the cost of electricity. This will require new approaches and technologies to be successful. N ...

    STTR Phase I 2010 Department of Energy
  6. A Mesh Free Framework for Mechanical Simulations of Microstructure Data Files

    SBC: CFD RESEARCH CORPORATION            Topic: 07a

    The Exascale Computing Project is tasked to develop the next generation of high performance computing systems capable of computing at 50 to 100 times faster than current HPC systems. Computing at this extreme-scale will significantly enhance the value of materials modeling and simulation to basic materials research and engineering In particular, computing at the extreme scale will enable a higher ...

    STTR Phase I 2019 Department of Energy
  7. A microfluidic ice nucleating particle counter for continuous measurements from small aerial platforms

    SBC: Handix Scientific Inc.            Topic: 23a

    Quantifying atmospheric aerosol, clouds and precipitation processes are critical needs for understanding and interpreting Earth’s changing energy budget, is a DOE objective, and is of broader benefit to the public. Specifically, the formation of ice in the atmosphere depends on the nature and abundance of ice nucleating particles, and has major implications for precipitation and cloud interactio ...

    STTR Phase I 2018 Department of Energy
  8. Amplifiers for High Repetition Rate Diode-Pumped Ultra-Intense Femtosecond Lasers

    SBC: XUV LASERS, INC.            Topic: 25c

    The problem being addressed is the development of high intensity ultrashort pulse lasers, in recognition that today’s ultra-high intensity lasers are limited to repetition rates of < 10 Hz. Technical solutions are sought to enable the generation of high energy (joule-level) laser pulses that can be focused to highly relativistic intensity at high repetition rates (100-1000 Hz). The proposed proj ...

    STTR Phase I 2019 Department of Energy
  9. A Multi-physics Analysis Capability for Engine Materials

    SBC: Sunergolab Inc.            Topic: 03b

    Computer-aided Engineering software that apply the Finite Element Method to perform a multi-physics analysis have received widespread acceptance for traditional macro-scale material systems. Challenges persist in the modeling of complex coupled processes in environmental/thermal barrier coatings (E/TBCs) used to protect substrate material against the corrosive environment in the hot section parts ...

    STTR Phase I 2019 Department of Energy
  10. Atomically Precise Membranes for the Separation of Hydrocarbons

    SBC: MAINSTREAM ENGINEERING CORP            Topic: 02a

    Separations often account for a majority of process costs. This is because all traditional separation processes have inherent weaknesses that prevent the system from achieving perfect (or even near perfect in many instances) selectivity. These weaknesses result in large recycle streams and require multiple separation units in concert in order to produce a product clean enough for use or sale. An a ...

    STTR Phase II 2018 Department of Energy
US Flag An Official Website of the United States Government