You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. A Collective Detection Based GPS Receiver for Small Satellites

    SBC: EMERGENT SPACE TECHNOLOGIES, INC.            Topic: T801

    To solve the problem of autonomous navigation on small satellite platforms less than 20 kg, we propose to develop an onboard orbit determination receiver for small LEO satellites which lack stable Attitude Determination and Control System (ADCS), continuous GPS coverage, or ground tracking. The system is a refinement of existing spaceborne receiver technology built around a new, innovative collec ...

    STTR Phase I 2013 National Aeronautics and Space Administration
  2. Additive Manufacture of Refractory Metal Propulsion Components

    SBC: Geoplasma, LLC            Topic: T9

    Niobium alloy (C-103) reaction control system (RCS) chambers have been used on numerous NASA programs. However at elevated temperatures, the strength of C-103 decreases significantly. Higher strength niobium alloys have been developed, but these alloys lack the formability of C-103. Recently, Additive Manufacture (AM) of niobium and C-103 has been demonstrated using powder bed electron beam me ...

    STTR Phase I 2018 National Aeronautics and Space Administration
  3. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: Senvol LLC            Topic: DLA18A001

    The Department of Defense (DoD) has a demand for out-of-production parts to maintain mission readiness of various weapons platforms. Additive manufacturing (AM) is an exciting and promising manufacturing technique that can make out-of-production parts and holds the potential to solve supply chain issues, such as high costs (i.e. for low-volume parts) and sole sourcing risks. The ability of AM to s ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  4. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  5. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: X-Wave Innovations, Inc.            Topic: DLA18A001

    Additive Manufacturing (AM) is a modern and increasingly popular manufacturing process for metallic components, but suffers from well known problems of inconsistent quality of the finished product. Process monitoring and feedback control are therefore crucial research areas with a goal of solving this problem. To address this concern, X-wave Innovations, Inc. (XII) and the University of Dayton Res ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  6. Advanced Li/CFx Primary Batteries with Non-Flammable Electrolytes

    SBC: CFX BATTERY, INC.            Topic: T601

    NASA seeks to develop high specific energy primary batteries that are safe and capable of performing under a wide temperature range, for manned space missions. To meet this goal, CFX Battery Inc. proposes to develop, characterize, and establish technological feasibility of a new Li/SF-CFx based high capacity lithium primary battery that offers higher rate capability and enhanced safety than conven ...

    STTR Phase I 2010 National Aeronautics and Space Administration
  7. Advanced Morphing Moulage for Medical Training (AMM-MT)

    SBC: Vcom3D, Inc.            Topic: DHA17A002

    For this Phase I SBIR proposal, Vcom3D proposes to design advanced medical moulage that accurately simulates the progression of an injury or pathology by morphing through a series of clinical states to enable learners to confirm the progression of the wound and to determine whether iatrogenic errors or pathologies occurred duing treatment. The physical morphing moulage may be applied to medical m ...

    STTR Phase I 2017 Department of DefenseDefense Health Agency
  8. Advanced Structural Health Monitoring System for Comprehensive Real-Time Vehicle Characterization

    SBC: AMERICAN GNC CORPORATION            Topic: T1

    In providing an innovative solution to improving information technologies and health management systems, AGNC is proposing a significant technological achievement with the Advanced Structural Health Monitoring System for Comprehensive Real-Time Vehicle Characterization. During in-flight conditions, this system is able to not only provide the status of information such as regarding the flight envel ...

    STTR Phase I 2010 National Aeronautics and Space Administration
  9. Advanced Unsteady Turbulent Combustion Simulation Capability for Space Propulsion Systems

    SBC: STREAMLINE NUMERICS, INC.            Topic: T901

    The innovation proposed here is a high performance, high fidelity simulation capability to enable accurate, fast and robust simulation of unsteady turbulent, reacting flows involving cryogenic propellants (such as LOX/LH2 and LOX/LCH4). The key features of this proposed capability are: (a) Hybrid RANS-LES (HRLES) methodology, and (b) flamelet modeling for turbulent combustion incorporated in a pr ...

    STTR Phase I 2010 National Aeronautics and Space Administration
  10. Aeroservoelastic Multifidelity Design of Biomimetic Aircraft (AMuBA)

    SBC: INTELLIGENT AUTOMATION, INC.            Topic: T15

    NASA has been investigating morphing aircraft for multi-mission capabilities and performance improvements in existing fixed-wing aircraft. In addition, the design of aeroelastic aircraft that can control the structural flexibility to their advantage, is an open area of research and development. In spite of the plethora of work on morphing aircraft and long slender wings, the goal of fielding such ...

    STTR Phase I 2018 National Aeronautics and Space Administration
US Flag An Official Website of the United States Government