You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Additive Manufacture of Refractory Metal Propulsion Components

    SBC: Geoplasma, LLC            Topic: T9

    Niobium alloy (C-103) reaction control system (RCS) chambers have been used on numerous NASA programs. However at elevated temperatures, the strength of C-103 decreases significantly. Higher strength niobium alloys have been developed, but these alloys lack the formability of C-103. Recently, Additive Manufacture (AM) of niobium and C-103 has been demonstrated using powder bed electron beam me ...

    STTR Phase I 2018 National Aeronautics and Space Administration
  2. Advanced Deposition Capability for Oxidation&Corrosion Protection Coatings

    SBC: Directed Vapor Technologies International, Inc.            Topic: T1201

    NASA's long range goals of reducing the fuel consumption by 30% and increasing fuel efficiency by 35% can be partially accomplished through increasing engine operation temperatures. As a result, the disk section is desired to operate in increasingly higher temperatures, which will subject it to additional degradation mechanisms of oxidation and hot corrosion. One approach to enhance the tem ...

    STTR Phase I 2013 National Aeronautics and Space Administration
  3. Advanced Unsteady Turbulent Combustion Simulation Capability for Space Propulsion Systems

    SBC: STREAMLINE NUMERICS, INC.            Topic: T901

    The innovation proposed here is a high performance, high fidelity simulation capability to enable accurate, fast and robust simulation of unsteady turbulent, reacting flows involving cryogenic propellants (such as LOX/LH2 and LOX/LCH4). The key features of this proposed capability are: (a) Hybrid RANS-LES (HRLES) methodology, and (b) flamelet modeling for turbulent combustion incorporated in a pr ...

    STTR Phase I 2010 National Aeronautics and Space Administration
  4. Air Vehicle Gust Response analysis for Conceptual Design

    SBC: Research In Flight, LLC            Topic: T15

    Research in Flight (RIF) and Auburn University are offering the development of an advanced, robust tool and methodology that allows the simulation and modeling of gust and wake vortex encounters for Distributed Electric Propulsion (DEP) enabled Urban Air Mobility (UAM) vehicle concepts. DEP enabled UAM concepts offer the potential for large performance improvements by exploiting favorable synergie ...

    STTR Phase I 2019 National Aeronautics and Space Administration
  5. An Additive Manufacturing Technique for the Production of Electronic Circuits

    SBC: MORNINGBIRD MEDIA CORPORATION            Topic: T1204

    The proposed 9-month research project aims for the development of additive manufacturing techniques for the creation of electronic devices. It will develop an innovative additive manufacturing technique that combines the ink-based printing with laser melting technology to directly print a three-dimensional (3D) system with built-in electrical properties and functioning as an electronic device. Th ...

    STTR Phase I 2016 National Aeronautics and Space Administration
  6. A Scalable Gas-Particle Flow Simulation Tool for Lander Plume-Surface Interaction and Debris Prediction

    SBC: CFD Research Corporation            Topic: T9

    Spacecraft propulsive landings on unprepared regolith present in extra-terrestrial environments pose a high risk for space exploration missions. Plume/regolith interaction results in (1) the liberation of dust and debris particles that may collide with the landing vehicle and (2) craters whose shape itself can influence vehicle dynamics. To investigate such gas-granular interactions for large-scal ...

    STTR Phase I 2018 National Aeronautics and Space Administration
  7. A Supported Liquid Membrane System for Steady State CO2 Control in a Spacecraft Cabin

    SBC: REACTION SYSTEMS, INC            Topic: T6

    Reducing the allowable concentration of carbon dioxide (CO2) in spacecraft is a critical need for NASA. The system now used on the International Space Station (ISS) is the carbon dioxide removal assembly (CDRA). While it has performed well on the ISS, managers have concluded that using the device to reach the new ppCO2 limit of 2.0 mm Hg is not practical and a new method is needed.In this projec ...

    STTR Phase I 2018 National Aeronautics and Space Administration
  8. Autonomous Navigation on Icy Moons and Ocean Worlds

    SBC: VETH RESEARCH ASSOCIATES LLC            Topic: T4

    Technology currently used for terrestrial navigation is extremely limited in the challenging environments on icy moons and ocean worlds such as Europa. Autonomous platforms used to collect data from beneath these ice and ocean surfaces cannot depend on access to satellite or any other electromagnetic communication. Autonomous systems in these environments are required to perform highly-complex tas ...

    STTR Phase I 2019 National Aeronautics and Space Administration
  9. Bi-Metallic Additive Manufacturing Close-Out of Coolant Channels for Large Liquid Rocket Engine (LRE) Nozzles

    SBC: Keystone Synergistic Enterprises, LLC            Topic: T1204

    This NASA sponsored STTR project will investigate methods for close-out of large, liquid rocket engine nozzle, coolant channels utilizing robotic laser and pulsed-arc additive manufacturing methods. Copper to Nickel alloy interface strength will be quantified and metallurgical characterization completed. A thermal model based on Rosenthal?s analytical expression for a moving heat source, which has ...

    STTR Phase I 2016 National Aeronautics and Space Administration
  10. Bio-mathematical Models of Aggregated Tissues & Organ Properties

    SBC: Corvid Innovation LLC            Topic: DHP16A001

    Realistic surgical simulation requires a combination of representative tissue geometry, accurate tissue material properties and lifelike tool-tissue interaction forces. Recent advances in computational power and imaging modalities have provided the capability to represent the anatomical details required for surgical training; however, the mathematical models which govern the underlying tissue pro ...

    STTR Phase I 2016 Department of DefenseDefense Health Agency
US Flag An Official Website of the United States Government