You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY20 is not expected to be complete until September, 2021.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Accelerating Metagenomics Using Graphics Processing Units

    SBC: Multicoreware, Inc.            Topic: 35a

    A key application of the technological breakthrough associated with decreased cost of DNA sequencing is metagenomics. Metagenomics is the process of sequencing DNA from whole ecosystems, rather than individuals or cultures. This approach has the potential to allow the dissection of microbial ecosystems in biofuel producing agricultural land, toxic contaminated sites and hydrocarbon recovery enviro ...

    STTR Phase I 2010 Department of Energy
  2. A Concrete Additive Manufacturing Process for Fixed and Floating Wind Turbine Foundations and Towers

    SBC: JC Solutions            Topic: 14b

    Tall towers and foundations for modern offshore and land-based wind turbines are too large to transport over roads or rail due to their extremely large dimensions. Existing “one-off” on-site construction methods are too expensive, and are too slow for manufacturing foundations and towers in the large numbers needed, especially for offshore components manufactured in ports with limited lay-down ...

    STTR Phase I 2018 Department of Energy
  3. Additive Manufacturing of Scalable 3D Resonators

    SBC: Global Research and Development Inc.            Topic: 29b

    This proposal is submitted in response to the SBIR/STTR Office of Science related to Quantum Information Science (QIS) Supporting Technologies. There is the need for fabrication techniques for scalable 3D Superconducting Radio Frequency (SRF) Structures for Quantum Information Systems. In this proposal we will develop an additive manufacturing approach to developing superconducting 3D microwave re ...

    STTR Phase I 2018 Department of Energy
  4. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  5. Advanced Membranes for CO2 Capture from Existing Coal-fired Power Plants

    SBC: Nextech Materials, Ltd.            Topic: 24a

    Coal is an abundant source of energy in the USA, but is not currently utilized effectively. Recently, the DOE has begun a carbon sequestration program is to develop advanced CO2 capture and compression technology for existing coal-fired plants with increased efficiency with no more than a 35% increase in the cost of electricity. This will require new approaches and technologies to be successful. N ...

    STTR Phase I 2010 Department of Energy
  6. A microfluidic ice nucleating particle counter for continuous measurements from small aerial platforms

    SBC: HANDIX SCIENTIFIC Inc.            Topic: 23a

    Quantifying atmospheric aerosol, clouds and precipitation processes are critical needs for understanding and interpreting Earth’s changing energy budget, is a DOE objective, and is of broader benefit to the public. Specifically, the formation of ice in the atmosphere depends on the nature and abundance of ice nucleating particles, and has major implications for precipitation and cloud interactio ...

    STTR Phase I 2018 Department of Energy
  7. Axisymmetric and Focusing Analyzers to Enable Efficient Powder and Residual Stress Neutron Diffractometers

    SBC: ADELPHI TECHNOLOGY INC            Topic: 12a

    Although thermal and cold neutron scattering is widely used, and is critical for success in many areas of materials science and engineering, relatively low neutron fluxes severely limit applications of not only laboratory neutrons generators, but also large national neutron facilities. State-of-the-art thermal and cold neutron sources are large expensive national facilities, which serve diverse co ...

    STTR Phase I 2018 Department of Energy
  8. Cavity Enhanced Thomson Scattering System for Low Temperature Plasmas

    SBC: Seaforth LLC            Topic: 30a

    Electrons play a very key role in plasma chemistry and dynamics of low temperature plasmas. Improved capability for measuring electron number density, ne, and electron energy distribution function, EEDF, in weakly ionized low temperature plasmas would benefit both fundamental study and application areas. For example, the capability would directly benefit emerging research targeted at modifying and ...

    STTR Phase I 2013 Department of Energy
  9. Coated Aerogel Electrodes for Photoelectrochemical Methanol Formation

    SBC: Innosense Llc            Topic: 11c

    Due to the current oil crisis, the United States has begun to focus on alternative energy sources for transportation and other domestic applications. Methanol offers a renewable alternative to many fossil fuels that can be a raw material for the synthetic hydrocarbons and their products. ISL proposes to fabricate a photo-electrochemical cell that converts carbon dioxide, a greenhouse gas which can ...

    STTR Phase I 2010 Department of Energy
  10. Defect Free, Ultra-Rapid Thinning/Polishing of Diamond Crystal Radiator Targets (20??m) for Highly Linearly Polarized Photon Beams

    SBC: Sinmat Inc            Topic: 46e

    The fabrication of high-quality ultra thin (~20 micron) diamond crystals targets for 9 GeV highly polarized photon beams is an outstanding challenge. Current state of the art polishing/thinning techniques are not successful in thinning single crystal diamond to such dimension because of its extreme hardness and chemical inertness. These techniques create significant stresses surface and sub-surfac ...

    STTR Phase I 2010 Department of Energy
US Flag An Official Website of the United States Government