You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY24 is not expected to be complete until March, 2025.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

The SBIR.gov award data files now contain the required fields to calculate award timeliness for individual awards or for an agency or branch. Additional information on calculating award timeliness is available on the Data Resource Page.

  1. Multi-Functional Nanotube-Based Sensor Array for Detecting Blood Coagulation Defects

    SBC: INNOSENSE CORPORATION            Topic: DHA19A001

    Defense Health Agency (DHA) is seeking a multi-functional diagnostic to determine blood coagulopathy in real time at point-of-care (POC). Blood coagulopathy, resulting in uncontrolled bleeding, is implicated in 80% of operating room deaths and 50% of trau

    STTR Phase I 2019 Department of DefenseDefense Health Agency
  2. Rapid Prototyped 3D Printed Filters for CW Agent Protection

    SBC: TDA RESEARCH, INC.            Topic: A18BT018

    Defense against chemical weapons is a critical DoD requirement. An effective defense requires the development of unique respirator systems that prevent inhalation of chemical warfare (CW) agents. In addition, the protective equipment exposed to CW agents must not pose a residual hazard after use in the battlefield. Existing respirator canisters remove CW agents, but they do not self-decontaminate ...

    STTR Phase I 2019 Department of DefenseArmy
  3. Passive Millimeter-Wave Imaging Camera System Using Optical Up-Conversion in Sparse Array Configuration

    SBC: NOVAA LTD            Topic: A18BT017

    The objective of this proposal is to enable high-sensitivity, passive imaging system of natural mm-wave emissions, which can be used as standalone or fused with other imaging modality such as conventional IR imagery in degraded environments. This is achieved through a unique antenna integrated electro-optic (EO) modulator, where received mm-wave signals modulate an optical carrier. The optical car ...

    STTR Phase I 2019 Department of DefenseArmy
  4. W-Band RF Instrumentation

    SBC: SRICO INC            Topic: A18BT002

    W-band millimeter waves have a number of important applications, including directed energy and, more recently, 5G FR2 network development. Reliable measurements of electric fields in the W-Band, while critical to the development of these applications, have proven challenging. This proposal addresses the development of an accurate, traceable, cost effective W-band RF field strength detector. The so ...

    STTR Phase I 2019 Department of DefenseArmy
  5. Signature Management Textiles

    SBC: CORNERSTONE RESEARCH GROUP INC            Topic: A18BT023

    The prolific nature of Advanced Battlefield and Ground surveillance radar (BSR/GSR) in military markets is driving the need to develop new methods of reducing infantry forces’ radar cross section (RCS) in effort to avoid detection and more freely move throughout the battlespace. One approach to combat the growing threat of BSR/GSR surveillance is through the development of advanced textiles that ...

    STTR Phase I 2019 Department of DefenseArmy
  6. High Linearity RF Amplifiers from Carbon Nanotubes

    SBC: CARBON TECHNOLOGY INC            Topic: A18BT004

    The Key to further improving the data rate in data communication while minimizing the power consumption is to improve the linearity of a power amplifiers in the system. Carbon Nanotube (CNT) offer intrinsically linear behavior, but to realize advanced linearity in a practical device requires high quality CNT material, and a fabrication process that can take the full advantage of the superior prope ...

    STTR Phase I 2019 Department of DefenseArmy
  7. Deep Ultraviolet Light Sources for Water Purification and Surface Sterilization

    SBC: TRIPLE RING TECHNOLOGIES INC            Topic: A18BT006

    This proposal is related to the development of high efficiency ultraviolet (UV) light emitting devices (LEDs) operating at 265 nm and 219 nm, which have the potential to replace conventional mercury lamps for many applications including dinsinfection and water purification. To date, the wall-plug efficiency of commercial LEDs operating at 265 nm is in the range of 2-3%, which has been limited by t ...

    STTR Phase I 2019 Department of DefenseArmy
  8. Software Tools for Scalable Quantum Validation and Verification

    SBC: SC SOLUTIONS, INC.            Topic: A18BT011

    In this Small Business Technology Transfer (STTR) Phase I project, SC Solutions, teaming with Sandia National Laboratories (SNL), will demonstrate the feasibility of a scalable Quantum Computing Validation & Verification (QCVV) tool that will allow quantum computing researchers to rapidly and conveniently test and benchmark their quantum computing systems. While several QCVV techniques have been d ...

    STTR Phase I 2019 Department of DefenseArmy
  9. Design of Easy-To-Use Structural Alloy Feedstocks for Additive Manufacturing

    SBC: ELEMENTUM 3D, INC.            Topic: A18BT003

    There is a need for easy-to-use, versatile alloys for additive manufacturing that print consistently regardless of the specific process or machine, or the metallurgical and manufacturing knowledge of the user. Such capability is especially critical for soldiers to be able to make every day items on demand in the theater of war. Toward meeting this need, recent successes developing high performance ...

    STTR Phase I 2019 Department of DefenseArmy
  10. Metal Additive Manufacturing with Minimal Post Processing (MaMMPP) (18-RD-116)

    SBC: UES INC            Topic: A18BT003

    Metal Additive Manufacturing (AM) research has typically addressed understanding how to maximize performance for an AM material, taking into account microstructural anisotropy, residual stress, defects (such as pores and lack of fusion defects), and surface finish. Optimizing a part then requires significant post processing such as hot isostatic pressing (HIP), heat treatment and surface finishing ...

    STTR Phase I 2019 Department of DefenseArmy
US Flag An Official Website of the United States Government