You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY22 is not expected to be complete until September, 2023.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. A Concrete Additive Manufacturing Process for Fixed and Floating Wind Turbine Foundations and Towers

    SBC: JC Solutions            Topic: 14b

    Tall towers and foundations for modern offshore and land-based wind turbines are too large to transport over roads or rail due to their extremely large dimensions. Existing “one-off” on-site construction methods are too expensive, and are too slow for manufacturing foundations and towers in the large numbers needed, especially for offshore components manufactured in ports with limited lay-down ...

    STTR Phase I 2018 Department of Energy
  2. Real-Time Distributed Quench Detection in High Temperature Superconductor Magnets

    SBC: Luna Innovations Incorporated            Topic: 20a

    Nuclear fusion has great potential for supplying global energy needs with a clean, abundant energy source. Advanced superconducting magnets will be used to contain the plasma at the center of the reactor. To operate these magnets, new sensors are needed to monitor the superconductors in real-time to detect the signs that the superconductor may quench (lose superconducting properties), so that corr ...

    STTR Phase I 2018 Department of Energy
  3. Low-cost, time-resolved chemical characterization of atmospheric aerosols

    SBC: Aerosol Devices Inc.            Topic: 23b

    Currently the chemical composition of atmospheric particulate matter is measured either by off-line analyses of time-integrated filter samples, or by in-situ instruments requiring near-constant operator oversight. These measurement approaches result in sparse or limited data coverage. Despite the critical role of composition on the health and environmental impacts of particulate matter, there exis ...

    STTR Phase I 2018 Department of Energy
  4. Low-cost and Flexible Transparent Electrodes Based on Ag–ZTOF (Zn–Sn–O–F) Amorphous Composites Through Ink-jet Printing

    SBC: HAZEN RESEARCH, INC.            Topic: 09b

    Sn-doped In2O3 (ITO) is the industry standard and most widely used transparent conducting electrode (TCE) because of its good electrical and optical properties. However, ITO has a number of disadvantages: ITO is not a suitable TCE for next-generation, high-efficiency, flexible OLEDs, because of its inappropriate work function, difficulty in creating desired patterns, low stability, delaminantion d ...

    STTR Phase I 2018 Department of Energy
  5. Extreme Temperature Distributed Sensing in Modular Energy Systems

    SBC: Luna Innovations Incorporated            Topic: 17b

    Fossil Energy (FE)-based modular power systems are a growing market that can meet the demand of rural and isolated areas both domestically and abroad. Many of these systems, also known as Radically Engineered Modular System (REMS), provide power and/or heat for farms, homes, and other industrial processes. The concept is to produce syngas (synthetic natural gas) from coal and readily available bio ...

    STTR Phase I 2018 Department of Energy
  6. Plug-In Hybrid Vehicle Optimization Using Vehicle-to-Cloud Connectivity

    SBC: Macchina, LLC            Topic: 13c

    Plug-in hybrid electric vehicles (PHEVs) represent a growing segment of the U.S. passenger vehicle market. An increasing number of PHEV models are available to consumers. PHEVs are similar to parallel hybrid vehicles like the Toyota Prius in that they have an electric motor and internal combustion engine that are used synergistically to significantly reduce fuel consumption while maintaining a nea ...

    STTR Phase I 2018 Department of Energy
  7. Scalable Polymerized Metal-Organic Frameworks with CO2-philic Rubbery Polymers for Membrane CO2/N2 Separation

    SBC: Helios-NRG, LLC            Topic: 18d

    As fossil fuels continue to serve as a major energy source, CO2 capture for utilization or sequestration is the only option to mitigate the CO2 emissions to the environment. However, the separation of CO2 from flue gas is an extremely costly proposition with existing technologies. Advanced membrane technology may address this challenge, if new membranes with CO2 permeance of 4,500 gpu and CO2/N2 s ...

    STTR Phase I 2018 Department of Energy
  8. Innovative, Multifunctional Layered Coatings for High Temperature Ceramic Matrix Composites

    SBC: RELIACOAT TECHNOLOGIES, LLC            Topic: 18a

    The design and realization of thermal/environmental barrier coatings systems for the protection and insulation of ceramic matrix composites that can withstand combustion temperatures approaching 3100 Fahrenheit is a formidable challenge. But that is necessary for achieving 65% efficiency target in future combined-cycle gas-turbine engines. A multifaceted research program is proposed to address thi ...

    STTR Phase I 2018 Department of Energy
  9. Additive Manufacturing of Scalable 3D Resonators

    SBC: GLOBAL RESEARCH & DEVELOPMENT INC            Topic: 29b

    This proposal is submitted in response to the SBIR/STTR Office of Science related to Quantum Information Science (QIS) Supporting Technologies. There is the need for fabrication techniques for scalable 3D Superconducting Radio Frequency (SRF) Structures for Quantum Information Systems. In this proposal we will develop an additive manufacturing approach to developing superconducting 3D microwave re ...

    STTR Phase I 2018 Department of Energy
  10. Development of Burst-mode Laser based High-speed Microwave and Thomson Scattering Instruments for Fusion Plasma Devices

    SBC: SPECTRAL ENERGIES LLC            Topic: 21a

    Fusion plasma devices at various DOE and international facilities need high-speed diagnostic tools to understand, predict, and control fusion plasmas. Thomson scattering (TS) at tens of Hz has routinely measured electron temperature (Te) and electron number density (ne) inside the plasma system. However, at these data rates traditional TS can obtain only a sparse data set, which significantly limi ...

    STTR Phase I 2018 Department of Energy
US Flag An Official Website of the United States Government