You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Rapid Combustion Driven High Pressure Powder Compaction of Refractory Alloys and Dispersion Strengthened Composites for High Temperature Applications

    SBC: UTRON KINETICS LLC            Topic: MDA09T002

    This Phase I STTR effort will be focused on fabricating and scientifically characterizing Mo/Re (59 Mo-41 Re), and W-25Re alloys with other alloying additions such as small % of dispersion strengthening materials such as zirconia, hafnia, tungsten carbide, Hafnium (Hf), Zirconium, TaC, Hf-based carbides in select geometrical shapes using UTRON Kinetics''s innovative, and cost-effective Combustion ...

    STTR Phase I 2010 Department of DefenseMissile Defense Agency
  2. Contamination-free, Ultra-rapid Reactive Chemical Mechanical Polishing (RCMP) of GaN substrates

    SBC: Sinmat Inc            Topic: MDA09T001

    Gallium Nitride (GaN) substrates are ideal materials for fabrication of high-power and high-frequency devices based on III-V materials. The current state-of-the-art Chemical Mechanical Polishing (CMP) methods are plagued by several challenges, including, surface charge affects due to surface contamination, and sub-surface damages, which can limit the quality of III-V devices. Furthermore, there is ...

    STTR Phase I 2010 Department of DefenseMissile Defense Agency
  3. Software Defined Multi-Channel Radar Receivers for X-band Radars

    SBC: DGNSS Solutions, LLC            Topic: MDA09T003

    The primary objective of the proposed research is to develop proof of concept of a software programmable X-Band radar system using low cost antenna array technology with digital beamforming architecture based on multiple receiver channels. The performance objectives will aim at a minimum of 400 MHz instantaneous bandwidth and a minimum instantaneous dynamic range of 52 dB. The objective of the t ...

    STTR Phase I 2010 Department of DefenseMissile Defense Agency
  4. Innovative Polishing Technology for Fabrication of High Performance Epi-ready GaSb Substrates

    SBC: Sinmat Inc            Topic: MDA12T003

    Antimony containing III-V semiconducting compounds are particularly attractive for the fabrication of a wide variety of electronic and optoelectronic devices such as photo detectors operating in the long wave infrared wavelength (12-32µm) range. The production of epi quality GaSb wafers still remains one of the important problems for rapid commercialization of GaSb devices. Sinmat Inc. proposes a ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  5. EOIR Fusion during Ascent Phase for C2BMC

    SBC: Vectraxx, Inc.            Topic: MDA12T004

    In this Phase I STTR project for MDA, Vectraxx of Glen Allen, Virginia will address the critical problem of dealing with pre-intercept debris fields and launch family clusters as seen by IR sensors. This is an essential element to the ascent phase component of the MDA"s Ballistic Missile Defense System. The objective of this R & D effort is to characterize pre-intercept debris field and leverage ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  6. M&S Uncertainty Quantification

    SBC: OPTIMIZATION TECHNOLOGIES, INC.            Topic: MDA12T007

    OptTek Systems, Inc (OptTek), proposes an affordable, effective UQ capability for both legacy and new BMDS M & S. The OptTek Team includes research institution partner Oak Ridge National Laboratory (ORNL) and subcontractor RTSync Corporation (RTSync). The proposed BMDS M & S UQ capability maximizes insertability into existing and future MDA BMDS M & S-supported Event processes, analysis methods, a ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  7. M&S Uncertainty Quantification

    SBC: Applied Biomathematics Inc            Topic: MDA12T007

    An emerging consensus in engineering holds that aleatory uncertainty should be propagated by traditional methods of probability theory but that epistemic uncertainty may require methods that do not confuse incertitude with variability by requiring every possibility be associated with a probability that it occurs. Therefore, although Monte Carlo shells that re-run calculations many times while var ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  8. Verification and Validation of Physics Based DPAL Models

    SBC: AEROSOFT INC            Topic: MDA12T008

    AeroSoft, with the USAFA Laser and Optics Research Center proposes to create an extensive and thorough Verification and Validation (V & V) Program for anchoring physics based modeling software for static and flowing DPAL systems. During Phase I, a review of existing experimental programs will made and used for preliminary validation with the GASP software suite. Once deficiencies in the current e ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  9. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  10. Smart Baseplate for Additive Manufacturing

    SBC: Luna Innovations Incorporated            Topic: DLA18A001

    Additive manufacturing (AM) has rapidly evolved into a valuable technique for making parts which, at times, cannot be fabricated through conventional machining methods.One challenge in the area of AM is the lack of real-time feedback on the fabrication process and the quality of the part being made.This is especially critical given the relatively long periods of time that complex parts can require ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
US Flag An Official Website of the United States Government