You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  2. Smart Baseplate for Additive Manufacturing

    SBC: Luna Innovations Incorporated            Topic: DLA18A001

    Additive manufacturing (AM) has rapidly evolved into a valuable technique for making parts which, at times, cannot be fabricated through conventional machining methods.One challenge in the area of AM is the lack of real-time feedback on the fabrication process and the quality of the part being made.This is especially critical given the relatively long periods of time that complex parts can require ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  3. Smart Baseplate for Additive Manufacturing

    SBC: Luna Innovations Incorporated            Topic: DLA18A001

    Additive manufacturing (AM) has rapidly evolved into a valuable technique for making parts which, at times, cannot be fabricated through conventional machining methods, or for fabrication of small quantities of complex parts. One challenge in the area of AM is the lack of real-time feedback on the fabrication process and the quality of the part being made. This is especially critical given the rel ...

    STTR Phase II 2019 Department of DefenseDefense Logistics Agency
  4. Virus-Like Particle Based pan-Marburgvirus Vaccine

    SBC: Luna Innovations Incorporated            Topic: CBD18A002

    Marburg virus (MARV) is a filamentous enveloped non-segmented negative sense RNA virus. This viruse is considered to be extremelydangerous with case fatality rates as high as 88-90%. Extensive efforts have gone towards effective vaccines for MARV prevention, however,none have been successfully established as licensed vaccines. Glycoprotein (GP) is the only surface protein of MARV. There are substa ...

    STTR Phase I 2018 Department of DefenseOffice for Chemical and Biological Defense
  5. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    This Phase II project aims to assemble the key set of sensor modalities that are needed to reliably view the key process anomalies and properties of laser powder bed fusion. The research team will down-select from the Phase I sensors investigated and integrate the sensors into a sensor fusion software package that facilitates data collection and synchronization, and eventually feedback control of ...

    STTR Phase II 2019 Department of DefenseDefense Logistics Agency
  6. Computerized Robotic Delayering and Polishing System

    SBC: Spectral Energies, LLC            Topic: DMEA18B001

    The proposed research and technical objectives in this project deal with computerized automatic delayering and polishing system that would be applicable to both commercial and government semiconductor device research and development with applications including Failure Analysis (FA), Fault Isolation (FI), and Reverse Engineering (RE) of semiconductor microelectronic devices. This project could hel ...

    STTR Phase I 2019 Department of DefenseDefense Microelectronics Activity
  7. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: SENVOL LLC            Topic: DLA18A001

    The Department of Defense (DoD) has a demand for out-of-production parts to maintain mission readiness of various weapons platforms. Additive manufacturing (AM) is an exciting and promising manufacturing technique that can make out-of-production parts and holds the potential to solve supply chain issues, such as high costs (i.e. for low-volume parts) and sole sourcing risks. The ability of AM to s ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
US Flag An Official Website of the United States Government