You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY22 is not expected to be complete until September, 2023.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Additive Manufacturing of Multifunctional Nanocomposites

    SBC: Sciperio, Inc.            Topic: A13AT010

    Sciperio with team members Georgia Institute of Technology and Centecorp have teamed up to develop an Additive Manufacturing Composite using nano and micro fillers. The team will develop multi-scale models that are supported by experimental characterization for advanced 3D Printable materials. Inelastic response of high strength hierarchical structures composed of engineered materials and specif ...

    STTR Phase I 2013 Department of DefenseArmy
  2. Conformal Li Metal Batteries Enabled By Microporous Electrodes

    SBC: Navitas Advanced Solutions Group, LLC            Topic: A18BT015

    Navitas will collaborate with the University of Maryland group to develop a flexible microporous Li metal anode. The proposed porous anode will reduce Li dendrite growth via its built-in porosity and increase rate capability via its high surface area. It will enable a conformal, safe, and light weight lithium metal batteries as soldier portable power devices. The Phase I project will demonstrate t ...

    STTR Phase I 2019 Department of DefenseArmy
  3. Cooperative Deployment of Next Generation Chemical Standoff Sensors

    SBC: MESH, INC            Topic: A10AT022

    MESH, Inc. has developed a method to take data from multiple fixed site standoff sensors and generate concentration maps using either triangulation or tomography. The programs that MESH has developed will be modified to allow standoff from moving platforms to be used in the data merging process. A simulation suite of tools, also developed by MESH, will be used to set the requirements on the accu ...

    STTR Phase I 2010 Department of DefenseArmy
  4. HIGH STRENGTH AND TOUGHNESS TUNGSTEN CARBIDE (WC) WITH NON-COBALT (Co) MATRICES

    SBC: UES INC            Topic: OSD12T07

    Cemented cobalt-tungsten carbide is a material with attractive properties including high hardness and fracture toughness that has found success in a wide variety of applications ranging from drilling bits to armor piercing projectiles. However, with the classification of cobalt as a strategic and critical material that the US Department of Health and Human Services has classified as"reasonably ant ...

    STTR Phase I 2013 Department of DefenseArmy
  5. Host-Targeted Antiviral Drugs Providing Rapid, Scalable, Stable, Broad-Spectrum MedicalCountermeasure Against Marburg Virus

    SBC: EVRYS BIO LLC            Topic: CBD18A002

    In a pandemic or exposure to weaponized Marburg virus the morbidity, mortality and social unrest that will ensue before vaccines orMilitary operating on foreign soil as well as to the population of the US Homeland. Practically all threat agents of biological origin (except forcertain non-proteinaceous toxins, typically produced by marine organisms and fungi) have their structure and vital function ...

    STTR Phase I 2018 Department of DefenseOffice for Chemical and Biological Defense
  6. Impact of Climate Change on Military Compounds in the Environment

    SBC: Environmental Quality Management            Topic: A09AT024

    This will facilitate the development of remedial approaches for existing facilities and assist in planning new facilities, logistics, and procedures to protect the environment without impairing critical mission functionality. The commercial application will include software distribution and updates.

    STTR Phase I 2010 Department of DefenseArmy
  7. Inferring Social and Psychological Meaning in Social Media

    SBC: SECURBORATION INC            Topic: A12aT009

    The rapid ascent and adoption of social media as the dominant form of communication has led to significant analysis challenges. In particular, there is a gap in theoretically informed methods to analyze data mined and collected from social media. One primary cause of this gap is the lack of fusing structural sources of information (e.g. social network topology) with non-structural sources (message ...

    STTR Phase I 2013 Department of DefenseArmy
  8. Low Cost Fabrication of Armor Protection Systems for Military Tactical Vehicles

    SBC: NexGen Composites LLC            Topic: A13AT021

    There is a great need and opportunity to develop lower cost manufacturing process for ceramic tile-based composite armor system for military tactical vehicles. The threat levels encountered by the military tactical vehicles, particularly due to the Improvised Explosive Devices (IED) pose an ever-increasing need for more lightweight and effective vehicle armor system at an affordable cost. A low-co ...

    STTR Phase I 2013 Department of DefenseArmy
  9. Membraneless Water Purification via Continuous, Self-Contained, Vacuum-Assisted Diffusiophoresis

    SBC: MAINSTREAM ENGINEERING CORP            Topic: A18BT005

    We propose the development of a membraneless water purification system using continuous, self-contained, vacuum-assisted diffusiophoresis. Using diffusiophoresis allows the system to clean water contaminated with particulates and bacteria without membranes or filters, while producing a stream of fresh, drinkable water. The system will operate using only electricity supplied by portable batteries/s ...

    STTR Phase I 2019 Department of DefenseArmy
  10. Metal Additive Manufacturing with Minimal Post Processing (MaMMPP) (18-RD-116)

    SBC: UES INC            Topic: A18BT003

    Metal Additive Manufacturing (AM) research has typically addressed understanding how to maximize performance for an AM material, taking into account microstructural anisotropy, residual stress, defects (such as pores and lack of fusion defects), and surface finish. Optimizing a part then requires significant post processing such as hot isostatic pressing (HIP), heat treatment and surface finishing ...

    STTR Phase I 2019 Department of DefenseArmy
US Flag An Official Website of the United States Government