You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY22 is not expected to be complete until September, 2023.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Contamination-free, Ultra-rapid Reactive Chemical Mechanical Polishing (RCMP) of GaN substrates

    SBC: Sinmat Inc            Topic: MDA09T001

    Gallium Nitride (GaN) substrates are ideal materials for fabrication of high-power and high-frequency devices based on III-V materials. The current state-of-the-art Chemical Mechanical Polishing (CMP) methods are plagued by several challenges, including, surface charge affects due to surface contamination, and sub-surface damages, which can limit the quality of III-V devices. Furthermore, there is ...

    STTR Phase I 2010 Department of DefenseMissile Defense Agency
  2. Software Defined Multi-Channel Radar Receivers for X-band Radars

    SBC: DGNSS Solutions, LLC            Topic: MDA09T003

    The primary objective of the proposed research is to develop proof of concept of a software programmable X-Band radar system using low cost antenna array technology with digital beamforming architecture based on multiple receiver channels. The performance objectives will aim at a minimum of 400 MHz instantaneous bandwidth and a minimum instantaneous dynamic range of 52 dB. The objective of the t ...

    STTR Phase I 2010 Department of DefenseMissile Defense Agency
  3. Innovative Polishing Technology for Fabrication of High Performance Epi-ready GaSb Substrates

    SBC: Sinmat Inc            Topic: MDA12T003

    Antimony containing III-V semiconducting compounds are particularly attractive for the fabrication of a wide variety of electronic and optoelectronic devices such as photo detectors operating in the long wave infrared wavelength (12-32µm) range. The production of epi quality GaSb wafers still remains one of the important problems for rapid commercialization of GaSb devices. Sinmat Inc. proposes a ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  4. M&S Uncertainty Quantification

    SBC: OPTIMIZATION TECHNOLOGIES, INC.            Topic: MDA12T007

    OptTek Systems, Inc (OptTek), proposes an affordable, effective UQ capability for both legacy and new BMDS M & S. The OptTek Team includes research institution partner Oak Ridge National Laboratory (ORNL) and subcontractor RTSync Corporation (RTSync). The proposed BMDS M & S UQ capability maximizes insertability into existing and future MDA BMDS M & S-supported Event processes, analysis methods, a ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  5. M&S Uncertainty Quantification

    SBC: Applied Biomathematics Inc            Topic: MDA12T007

    An emerging consensus in engineering holds that aleatory uncertainty should be propagated by traditional methods of probability theory but that epistemic uncertainty may require methods that do not confuse incertitude with variability by requiring every possibility be associated with a probability that it occurs. Therefore, although Monte Carlo shells that re-run calculations many times while var ...

    STTR Phase I 2013 Department of DefenseMissile Defense Agency
  6. Additive Manufacturing Sensor Fusion Technologies for Process Monitoring and Control.

    SBC: ARCTOS Technology Solutions, LLC            Topic: DLA18A001

    Universal Technology Corporation (UTC) has teamed with the University of Dayton Research Institute (UDRI), Stratonics, and Macy Consulting to demonstrate not only the transitionability into commercial systems, but also to develop the data analytics and monitoring and control requirements to extract the full value fromseveral sensors, including the Stratonics ThermaViz, acoustic and profilometry se ...

    STTR Phase I 2018 Department of DefenseDefense Logistics Agency
  7. Rapid SERS-based Detection of Sepsis and TBI Biomarkers

    SBC: Ionica Sciences, Inc            Topic: DHA17B004

    Traumatic brain injury (TBI) often occurs when a sudden trauma or head injury disrupts the function of the brain. Common causes of TBI include damage caused by explosive devices, falls and vehicle or motorcycle accidents. Sepsis is the result of a massive immune response to bacterial infection that gets into the blood. Sepsis often leads to organ failure or injury, and has always been a significan ...

    STTR Phase I 2018 Department of DefenseDefense Health Agency
  8. Oxygen Production and Delivery on Demand

    SBC: GLOBAL RESEARCH & DEVELOPMENT, INC.            Topic: DHA17B005

    This proposal is in response to the Defense Health Agency 2017 Phase I SBIR topic 17B-005.The approach is the use of a membrane oxygen pump using newly developed nano-thickness membranes with all the layers less than 1 micron total.Nanometer thickness membranes enable more oxygen output per surface area at temperatures of 300-600 C than current state-of-the -art 600-800 C membranes that are 50-300 ...

    STTR Phase I 2018 Department of DefenseDefense Health Agency
  9. Test Article Printing with Laser Additive Manufacturing (TAP-LAM) for Threat Surrogate Target Production

    SBC: MV Innovative Technologies LLC (DBA: Opt            Topic: MDA17T001

    Optonicus proposes development of the TAP-LAM (Test Article Printing with Laser Additive Manufacturing for Threat Surrogate Target Production) powder bed fusion and directed energy depositions systems. The TAP-LAM metal additive manufacturing system will advance strategic missile defense system testing capabilities by improving 3D printing methods to rapidly produce large-scale threat surrogate ta ...

    STTR Phase I 2018 Department of DefenseMissile Defense Agency
  10. Additive Manufacturing of Metallic Materials for High Strain Rate Applications

    SBC: MRL MATERIALS RESOURCES LLC            Topic: MDA17T001

    Metallic additive manufacturing (AM) is an attractive technology for the production of lethality test articles due to the potential for significantly reduced lead time and manufacturing cost.However, in order to be effective in providing accurate lethality data, the properties of the AM material have to match closely the properties of conventionally manufactured alloys found in real threat targets ...

    STTR Phase I 2018 Department of DefenseMissile Defense Agency
US Flag An Official Website of the United States Government