You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. Low Power Long Wave Infrared Laser Sources

    SBC: Aculight Corporation            Topic: N/A

    With new detectors capable of sensing 7.5 - 9 micron wavelengths, a future threat is emerging since these detectors can be used in seekers. The need is to counter this threat with a laser source operating at 7.5 - 9 microns. The source requirements are 5 - 10 Watts of average power and a repetition rate of > 10 kHz. The proposed laser source is a Nd:YAG-pumped tandem OPO system consisting o ...

    SBIR Phase I 1997 Department of DefenseNavy
  2. Low-cost, high brightness, short-pulse eyesafe solid-state laser transmitter for long-range missile defense

    SBC: Aculight Corporation            Topic: N/A

    For future long-range theater ballistic missile defense, aircraft-mounted LADAR systems require eyesafe laser transmitters that produce higher pulse energy and better beam quality than currently available optical parametric oscillators (OPOs) pumped by diode-pumped Nd:YAG lasers. Aculight proposes a novel laser transmitter approach that can simultaneously generate the required pulse energy, b ...

    SBIR Phase I 1997 Department of DefenseNavy
  3. Compact, High Pulse Rate, Mid-Infrared laser

    SBC: Aculight Corporation            Topic: N/A

    N/A

    SBIR Phase I 1996 Department of DefenseNavy
  4. Catalytic Conversion Recycling Process for Composite Aircraft Components

    SBC: Adherent Technologies, Inc.            Topic: N/A

    Cured aircraft composite materials present a particularly difficult challenge for recycling technology. Those materials have mostly thermosetting epoxy matrices and occur in intimate association with metals, paints, and coatings. Current techniques for recycling thermoset composites, mostly for automotive sheet molding compounds (SMC), involve pulverizing the material for use as fillers. Th ...

    SBIR Phase I 1996 Department of DefenseNavy
  5. Tertiary Recycling Process for Shipboard Plastic Processor Product

    SBC: Adherent Technologies, Inc.            Topic: N/A

    A novel tertiary recycling process is proposed for investigation as an economical means for recycling shipboard plastic waste. Early development work has shown that this process can convert a wide variety of polymers and composites into low molecular weight hydrocarbons at temperatures below 200'C. The hydrocarbons produced can then be reused as chemicals, fuels, or monomers. Metal, glass, and fil ...

    SBIR Phase I 1996 Department of DefenseNavy
  6. Prediction Method for Hydrodynamic Problems of Two Bodies Operating in Close Proximity

    SBC: Targazyme, Inc.            Topic: N/A

    N/A

    SBIR Phase I 1994 Department of DefenseNavy
  7. Lighter-Than-Air Optical Platform

    SBC: Applied Research Associates, Inc.            Topic: N/A

    A miniaturized lighter-than-air (LTA) unmanned air vehicle (UAV) is proposed as a low altitude, station keeping, optical instrumentation platform. The advanced airship design will be derived from parameters developed during the successful Small Aerostat Surveillance System, Low Intensity Target Exploitation (SASS LITE) UAV program. This miniature airship developed by Applied Research Associates, I ...

    SBIR Phase I 1994 Department of DefenseNavy
  8. Methodology to Predict Ballistic Penetration and Damage of Composite Laminated Structures

    SBC: Applied Research Associates, Inc.            Topic: N/A

    Current utilization of composite materials in air and surface weapons systems and structures is extensive, and the use of these materials can be expected to increase in the future. Weapons effectiveness assessments and the design of protective structures require methodologies to predict the terminal ballistic interactions between projectiles and fragments penetrating composite laminated target st ...

    SBIR Phase I 1996 Department of DefenseNavy
  9. Engineering Models of Reactive Munitions and Damage Effects

    SBC: Applied Research Associates, Inc.            Topic: N/A

    Warhead design calculations and weapons effectiveness estimates require a methodology to predict structural response and the associated damage to air targets from reactive munitions. The objectives for the proposed Phase I study effort are to develop candidate launch conditioning, reaction initiation and reaction rate methodology, to incorporate existing ballistic, blast and quasi-static pres ...

    SBIR Phase I 1997 Department of DefenseNavy
  10. Missile Battery Damage Prediction Methodology

    SBC: Applied Research Associates, Inc.            Topic: N/A

    N/A

    SBIR Phase I 1992 Department of DefenseNavy
US Flag An Official Website of the United States Government