List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. A Remote Egg-oiling System with Autonomous and Automated Target Object Identification for Nuisance Bird Management

    SBC: Hitron Technologies Inc.            Topic: N183142

    Leveraging our experience and expertise in robot development and system integration (hardware and software) as well as deep learning for agricultural applications, Hitron Technologies Inc. (HTI) proposes to develop an Intelligent Remote Egg Oiling System (IREOS), with the collaboration of University of South Carolina (USC). The IREOS allows for effective nuisance bird management by performing auto ...

    SBIR Phase I 2019 Department of DefenseNavy
  2. SBIR Phase I: HIGH CAPACITY ENERGY STORAGE ANODE MATERIAL

    SBC: Hexalayer, LLC            Topic: MN

    The broader impact/commercial potential of this Small Business Innovation Research (SBIR) project is the development and widespread adaptation of next generation energy storage devices. With high energy density advanced materials, these devices can store significantly higher electric power per single charge. Particularly, rechargeable batteries with significantly higher energy density will improve ...

    SBIR Phase I 2019 National Science Foundation
  3. A Modified GMAW System for Distortion Reduction and Travel Speed Increase through Separate Heat Input and Deposition Rate Control

    SBC: ADAPTIVE INTELLIGENT SYSTEMS            Topic: N07211

    In traditional GMAW and modifications, the current melting the wire is the same as the current heating the base metal. To maintain a minimally acceptable productivity, the base metal heat input is typically much greater than the required to control the distortion at an acceptable or desirable level. In the modified GMAW proposed, a bypass torch is added to an existing GMAW system to bypass part of ...

    SBIR Phase II 2009 Department of DefenseNavy
  4. Highly Corrosion Resistant Aluminum Alloys: Innovative Processing Methods to Enhanced Corrosion Resistance (e.g., layered structures, etc.)

    SBC: ATI, INC.            Topic: OSD09C03

    Two different approaches will be investigated for producing aluminum alloys with a layer structure that have mechanical properties similar to Al 7050-T7 and Al 7075-T6 and greatly improved corrosion resistance. Layered aluminum alloys will be produced using the Novelis-Fusion™ casting process. This process is very cost effective and has been demonstrate on commercial products. The other appro ...

    SBIR Phase I 2009 Department of DefenseNavy
  5. Innovative Methodologies for the Development of a High Strength, Anodize-Free Corrosion Resistant, Aerospace Aluminum Alloys

    SBC: ATI, INC.            Topic: OSD09C02

    The objective of this program is develop high strength aluminum alloys ( as high strength as that of 7075-T6) that would not require anodization to achieve corrosion resistance. Among the Al alloy systems, only 7xxx and Al-Cu-Li alloy systems are capable of such a high strength level of 7075-T6 properties ( design minimum tensile yield stress of 75 ksi). Therefore, only these two alloy systems ...

    SBIR Phase I 2009 Department of DefenseNavy
  6. SBIR PhaseI: Split Amine Absorbent for CO2 Capture from Post Combustion Flue Gas of Coal Fired Power Plants

    SBC: 3 H Company            Topic: BC

    This Small Business Innovation Research Phase I project is to demonstrate an innovative low cost, low energy-consuming, and novel CO2 capture technology based on a process entitled ?Split Amine Absorption?. The Phase I objective is to develop data necessary to confirm the principle of the concept and to identify at least one set of optimum absorbent composition for the CO2 capture from flue gas of ...

    SBIR Phase I 2009 National Science Foundation
  7. SBIR Phase I: Plasma Thermograms for Disease Detection and Monitoring

    SBC: Louisville Bioscience, Inc.            Topic: BC

    This Small Business Innovation Research Phase I project is to develop and commercialize a powerful new diagnostic assay platform for quantitative analysis of plasma from human blood using Differential Scanning Calorimetry. The platform will form the basis for generating novel high-throughput diagnostic assays requiring minimal sample handling and processing that can be performed in an hour on a si ...

    SBIR Phase I 2009 National Science Foundation
  8. SBIR Phase II: Improved Manufacturing Methodology for Aluminum Ash Metal Matrix Composite Materials

    SBC: NuForm Materials, LLC            Topic: AM

    This award is funded under the American Recovery and Reinvestment Act of 2009 (Public Law 111-5). This Small Business Innovation Research(SBIR)Phase II project seeks to overcome the principal impediments of the inconsistent quality of metal matrix composite (MMC) materials from fly ash and aluminum. This project utilizes highly processed ash derived ceramics (ADC) as a reinforcing phase in alumin ...

    SBIR Phase II 2009 National Science Foundation
  9. SBIR Phase II: Low Cost-Reduced Risk Manufacturing Process For Nanocoatings

    SBC: Topasol LLC            Topic: AM

    This award is funded under the American Recovery and Reinvestment Act of 2009 (Public Law 111-5). This Small Business Innovation Research (SBIR) Phase II project seeks to reduce the cost and risk of manufacturing nanoparticle/resin blends for coatings. Currently nanocoating resin manufacturing requires two steps; the first is the production of nanoparticles ex-situ of the coating resin using plas ...

    SBIR Phase II 2009 National Science Foundation
  10. SBIR Phase II: Lens-forming nanocomposites for high strength, clear ophthalmic lenses

    SBC: Vision Dynamics, LLC            Topic: EO

    This Small Business Innovation Research (SBIR) Phase II project addresses the development of a UV curable bulk nanocomposite having enhanced optical and mechanical properties for ophthalmic lenses. The work focuses the incorporation of metal oxide nanoparticles into a transparent polymer to engineer the refractive index and mechanical properties. This requires the synthesis of stable nanoparticles ...

    SBIR Phase II 2009 National Science Foundation

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government