List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. A Remote Egg-oiling System with Autonomous and Automated Target Object Identification for Nuisance Bird Management

    SBC: Hitron Technologies Inc.            Topic: N183142

    Leveraging our experience and expertise in robot development and system integration (hardware and software) as well as deep learning for agricultural applications, Hitron Technologies Inc. (HTI) proposes to develop an Intelligent Remote Egg Oiling System (IREOS), with the collaboration of University of South Carolina (USC). The IREOS allows for effective nuisance bird management by performing auto ...

    SBIR Phase I 2019 Department of DefenseNavy
  2. A Modified GMAW System for Distortion Reduction and Travel Speed Increase through Separate Heat Input and Deposition Rate Control

    SBC: ADAPTIVE INTELLIGENT SYSTEMS            Topic: N07211

    In traditional GMAW and modifications, the current melting the wire is the same as the current heating the base metal. To maintain a minimally acceptable productivity, the base metal heat input is typically much greater than the required to control the distortion at an acceptable or desirable level. In the modified GMAW proposed, a bypass torch is added to an existing GMAW system to bypass part of ...

    SBIR Phase II 2009 Department of DefenseNavy
  3. Highly Corrosion Resistant Aluminum Alloys: Innovative Processing Methods to Enhanced Corrosion Resistance (e.g., layered structures, etc.)

    SBC: ATI, INC.            Topic: OSD09C03

    Two different approaches will be investigated for producing aluminum alloys with a layer structure that have mechanical properties similar to Al 7050-T7 and Al 7075-T6 and greatly improved corrosion resistance. Layered aluminum alloys will be produced using the Novelis-Fusion™ casting process. This process is very cost effective and has been demonstrate on commercial products. The other appro ...

    SBIR Phase I 2009 Department of DefenseNavy
  4. Innovative Methodologies for the Development of a High Strength, Anodize-Free Corrosion Resistant, Aerospace Aluminum Alloys

    SBC: ATI, INC.            Topic: OSD09C02

    The objective of this program is develop high strength aluminum alloys ( as high strength as that of 7075-T6) that would not require anodization to achieve corrosion resistance. Among the Al alloy systems, only 7xxx and Al-Cu-Li alloy systems are capable of such a high strength level of 7075-T6 properties ( design minimum tensile yield stress of 75 ksi). Therefore, only these two alloy systems ...

    SBIR Phase I 2009 Department of DefenseNavy
  5. Air-sea flux, Turbulence, Aerosol and Wave Measurement System

    SBC: ZIVKO AERONAUTICS, INC.            Topic: N08190

    This Navy SBIR Phase II program looks at the updating (both structural and electronics) of the current Controlled Towed Vehicle (CTV) and the fabrication of a new mount/enclosure that will allow for the mounting of the CTV system on a standard military style wing plyon. The vehicle is primarily for use in atmospheric research, specifically the surface flow over the ocean. Towed behind a research a ...

    SBIR Phase II 2009 Department of DefenseNavy
  6. DESIGN OF AN AUTOMATED BEST SIGNAL SOURCE COMBINER

    SBC: FRONTIER ENGINEERING            Topic: N/A

    CURRENT BEST TELEMETRY SOURCE COMBINER SYSTEMS USED AT WEAPONS TEST RANGES ARE CAPABLE OF SELECTING THE "BEST" SIGNAL FROM SEVERAL REDUNDANT SOURCES. HIGHER DATA RATES AND DETERIORATION OF TEST RANGE SNRS HAVE PRECIPITATED A REQUIREMENT FOR AN AUTOMATED TELEMETRY SIGNAL PROCESSING SYSTEM CAPABLE OF COMBINING AVAILABLE SOURCES INTO AN ENHANCED "BEST SIGNAL."

    SBIR Phase I 1987 Department of DefenseNavy
  7. EXPAND NEW BONDED SEAM TECHNOLOGY IN THE ASSEMBLY OF GARMENTS- RESEARCH DESIGN STUDY

    SBC: Ssunnol Inc.            Topic: N/A

    SSUNNOL INC. IS PRESENTLY USING ITS PATENTED TECHNOLOGY OF INJECTION SEAM TO PRODUCE LIGHT WEIGHT COTTON GLOVES FOR THE U.S. NAVY, TVA, AND OTHER NUCLEAR POWER PLANT OPERATORS. FIVE MILLION PAIRS HAVE BEEN PRODUCED SINCE 1984, WITH 8 MILLION ON BACKLOG. AN INDIVIDUAL GLOVE CAN BE PRODUCED IN ONE SECOND AS COMPARED TO 30 SECONDS BY STITCHING. PRINCIPAL PURPOSE OF THE PROPOSED DESIGN STUDY WILL BE T ...

    SBIR Phase II 1987 Department of DefenseNavy

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government