List

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY19 is not expected to be complete until April, 2020.

  1. A Remote Egg-oiling System with Autonomous and Automated Target Object Identification for Nuisance Bird Management

    SBC: Hitron Technologies Inc.            Topic: N183142

    Leveraging our experience and expertise in robot development and system integration (hardware and software) as well as deep learning for agricultural applications, Hitron Technologies Inc. (HTI) proposes to develop an Intelligent Remote Egg Oiling System (IREOS), with the collaboration of University of South Carolina (USC). The IREOS allows for effective nuisance bird management by performing auto ...

    SBIR Phase I 2019 Department of DefenseNavy
  2. A Modified GMAW System for Distortion Reduction and Travel Speed Increase through Separate Heat Input and Deposition Rate Control

    SBC: ADAPTIVE INTELLIGENT SYSTEMS            Topic: N07211

    In traditional GMAW and modifications, the current melting the wire is the same as the current heating the base metal. To maintain a minimally acceptable productivity, the base metal heat input is typically much greater than the required to control the distortion at an acceptable or desirable level. In the modified GMAW proposed, a bypass torch is added to an existing GMAW system to bypass part of ...

    SBIR Phase II 2009 Department of DefenseNavy
  3. Highly Corrosion Resistant Aluminum Alloys: Innovative Processing Methods to Enhanced Corrosion Resistance (e.g., layered structures, etc.)

    SBC: ATI, INC.            Topic: OSD09C03

    Two different approaches will be investigated for producing aluminum alloys with a layer structure that have mechanical properties similar to Al 7050-T7 and Al 7075-T6 and greatly improved corrosion resistance. Layered aluminum alloys will be produced using the Novelis-Fusion™ casting process. This process is very cost effective and has been demonstrate on commercial products. The other appro ...

    SBIR Phase I 2009 Department of DefenseNavy
  4. Innovative Methodologies for the Development of a High Strength, Anodize-Free Corrosion Resistant, Aerospace Aluminum Alloys

    SBC: ATI, INC.            Topic: OSD09C02

    The objective of this program is develop high strength aluminum alloys ( as high strength as that of 7075-T6) that would not require anodization to achieve corrosion resistance. Among the Al alloy systems, only 7xxx and Al-Cu-Li alloy systems are capable of such a high strength level of 7075-T6 properties ( design minimum tensile yield stress of 75 ksi). Therefore, only these two alloy systems ...

    SBIR Phase I 2009 Department of DefenseNavy
  5. Sensor for Continuous Detection and Reporting of Total Residual Oxidant in Hypochlorite-Enhanced Water Systems

    SBC: Pronghorn Technologies, LLC            Topic: N092152

    The U.S. Navy has significantly improved its operational capabilities in littoral and near-shore seawaters, which has resulted in the need to achieve much better pre-treatment of the seawater withdrawn from the often turbid and debris-filled shallow waters for the onboard desalination systems. Low-maintenance microfiltration is now used for pre-treatment, and it relies upon periodic electrolytic h ...

    SBIR Phase I 2009 Department of DefenseNavy
  6. Lightweight Roadside Blast Protection

    SBC: Kennon Products, Inc.            Topic: N09T032

    One of the greatest threats to American armed forces serving in Iraq and Afghanistan is the damage caused by mines, roadside bombs, and improvised explosive devices (IEDs). The wide variety of device types, and increasing sophistication of these weapons, presents a growing challenge to protecting U.S. warfighters. Currently, personnel vehicles are protected with thick, heavy armor that severely ...

    STTR Phase I 2009 Department of DefenseNavy
  7. Advanced Composite Boats

    SBC: Kennon Products, Inc.            Topic: N091049

    This proposal seeks to develop, refine, and combine, several promising composites construction techniques in order to produce lighter, stronger, more agile boats, ultimately at reduced acquisition costs. These techniques rely on sophisticated uses of fibers and fiber layups, advanced methods of resin infusion, and novel combinations of fabrication methods. The boats proposed will be “unibody-” ...

    SBIR Phase I 2009 Department of DefenseNavy
  8. CASE FOR CONTROLLERS

    SBC: Compu Systems Corp            Topic: N/A

    THIS PHASE I PROPOSAL IS FOR THE DESIGN OF THE GENERAL PURPOSE CASE SYSTEM THAT WILL AID IN THE DEVELOPMENT OF FIRMWARE AND SOFTWARE FOR GENERAL PURPOSE CONTROLLERS. THE LONG-TERM OBJECTIVE OF THE PROPOSED RESEARCH IS THE DEVELOPMENT OF A PERSONAL COMPUTER, PC, BASED SYSTEM THAT WILL ALLOW KNOWLEDGEABLE APPLICATION ENGINEERS TO CREATE THE FIRMWARE FOR A GENERAL PURPOSE CONTROLLER.

    SBIR Phase I 1987 Department of DefenseNavy

Agency Micro-sites

SBA logo
Department of Agriculture logo
Department of Commerce logo
Department of Defense logo
Department of Education logo
Department of Energy logo
Department of Health and Human Services logo
Department of Homeland Security logo
Department of Transportation logo
Environmental Protection Agency logo
National Aeronautics and Space Administration logo
National Science Foundation logo
US Flag An Official Website of the United States Government