You are here

Award Data

For best search results, use the search terms first and then apply the filters
Reset

The Award database is continually updated throughout the year. As a result, data for FY21 is not expected to be complete until September, 2022.

Download all SBIR.gov award data either with award abstracts (290MB) or without award abstracts (65MB). A data dictionary and additional information is located on the Data Resource Page. Files are refreshed monthly.

  1. A LOW-COST OPTICAL WEATHER IDENTIFIER FOR AN AUTOMATED WEATHER OBSERVING SYSTEM

    SBC: DYNAMICS TECHNOLOGY, INC.            Topic: N/A

    THE IDENTIFICATION OF THE TYPE OF PRECIPITATION (RAIN, SNOW, FOG/HAZE, HAIL) HAS TRACTIONALLY RELIED ON HUMAN JUDGMENT. RECENTLY, THE WAVE PROPAGATION LABORATORY OF DEVELOPED A TECHNOLOGY FOR AUTOMATIC WEATHER IDENTIFICATION USING LASER SCINTILLATION AND SCATTERING. THE TECHNIQUE HAS BEEN SUCCESSFULLY TESTED IN FIELD OPERATION. HOWEVER, THE SYSTEM IS TOO CLUMSY AND EXPENSIVE FOR LARGE-SCALE FIELD ...

    SBIR Phase II 1985 Department of Transportation
  2. EMBEDDED PAVEMENT STRESS SENSORS CONTAINING PIEZOELECTRIC COMPOSITES

    SBC: Fiber Materials, Inc.            Topic: N/A

    FIBER MATERIALS, INC. (FMI) PROPOSES SENSORS WHICH CAN BE EMBEDDED IN PAVEMENT TO MEASURE STRESS AND STRAIN FROM TRUCKS PASSING OVER AT SPEEDS UP TO 60 MPH. THESE SIMPLE, DURABLE SENSORS WILL BE MADE FROM PIEZOELECTRIC COMPOSITES WHICH ACT AS PASSIVE SENSORS AND DEVELOP A CHARGE PROPORTIONAL TO THE APPLIED PRESSURE. THE CHARGE IS CONVERTED TO A VOLTAGE WHICH IS RECORDED ON NEARBY EQUIPMENT. THE PH ...

    SBIR Phase II 1995 Department of Transportation
  3. MEASURING RETROREFLECTIVITY OF PAVEMENT MARKINGS

    SBC: Advanced Retro Technology Inc.            Topic: N/A

    THE MEASUREMENT OF THE RETROREFLECTIVITY OF PAVEMENT MARKINGS OR TRAFFIC STRIPING HAS BEEN LIMITED BY THE INSTRUMENTATION AT PRESENT. THE MAJORITY OF THESE INSTRU- MENTS ARE HAND-HELD PORTABLE UNITS WITH LIMITED GEOMETRY ANDNEASUREMENT AREA. MOBLE UNITS BUILT BY SOME STATES ALSO ARE LIMITED IN THEIR PERFORMANCE BY STRAY LIGHT, NON-OPTIMUM GEOMETRY AND OTHER PROBLEMS. A NEW RETROREFLECTOMETER IS PR ...

    SBIR Phase II 1987 Department of Transportation
  4. LOW COST SMART MAGNETOMETER FOR TRAIN DETECTION/MONITORING

    SBC: KVH INDUSTRIES, INC.            Topic: N/A

    PRESENT TRAIN DETECTION SCHEMES RELY LARGELY ON A LOW RESISTANCE THROUGH THE TRAIN'S WHEELS TO PERTURBATE A STABLE ELECTRICAL CIRCUIT. WHILE ELEGANT IN PRINCIPLE, THE DESIGN IS PLAGUED BY OXIDE FILMS AND MATERIAL BUILDUP ON THE RAIL, SNEAK PATHS THROUGH THE BALLAST AND OTHER UNCONTROLLABLE VARIABLES. KVH INDUSTRIES PROPOSES TO DESIGN AND DELIVER A "SMART MAGNETOMETER"-BASED SENSOR PACKAGE WHICH WI ...

    SBIR Phase II 1995 Department of Transportation
  5. SmartCross-Traffic Signal Interface on the Smartphone

    SBC: Savari Inc.            Topic: 111FH1

    On average, a pedestrian is killed every 2 hours and injured every 8 minutes in traffic crashes. 73% of these fatalities occur in urban areas. The SmartCross system aims to reduce the risk of vehicle-pedestrian crashes by providing situational awareness to the pedestrian as well as the vehicle approaching a crosswalk. The system makes use of the proliferation of smartphones to provide audio, visua ...

    SBIR Phase II 2016 Department of Transportation
  6. Reinforced Additively Manufactured Compression Assisted Molding (RAMCAM) of On-Demand Environmentally Stable Structural Composite Parts

    SBC: SAN DIEGO COMPOSITES, INC.            Topic: DLA152001

    San Diego Composites, Inc. (SDC) is developing the Reinforced Additively Manufactured Compression Assisted Molding (RAMCAM) pod to produce on-demand, corrosion resistant, aluminum and stainless steel equivalent parts in less than three days. RAMCAM combines the advantageous 2 day lead time of custom parts produced by 3D printing with the 1 day forging of structural parts via composite compression ...

    SBIR Phase II 2016 Department of DefenseDefense Logistics Agency
  7. Seamless Flexible Fuel Tanks- 65% TOC Reduction

    SBC: Response Technologies, LLC            Topic: DLA152001

    The DoD uses flexible fuel bladders in multiple air, ground, and sea vehicles because they: 1) easily fit into almost any space, 2) are corrosion resistant, and can often be self-sealing and explosion resistant, 3) allow for customized placement of fittings and connection points, and 4) these flexible tanks can collapse as they empty, thereby reducing the need for venting and minimizing sloshing a ...

    SBIR Phase II 2016 Department of DefenseDefense Logistics Agency
US Flag An Official Website of the United States Government